smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Fujitsu MHY BH
Device Model:     FUJITSU MHY2250BH
Serial Number:    --
LU WWN Device Id: 5 00000e ...
Firmware Version: 0081000D
User Capacity:    250,059,350,016 bytes [250 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 3f
SATA Version is:  SATA 2.5, 1.5 Gb/s
Local Time is:    Sat Jan 29 15:47:13 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is:     254 (maximum performance), recommended: 254
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (  25)	The self-test routine was aborted by
					the host.
Total time to complete Offline 
data collection: 		( 1009) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 143) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   100   046    -    0
  2 Throughput_Performance  P-S---   100   100   030    -    0
  3 Spin_Up_Time            PO----   100   100   025    -    0
  4 Start_Stop_Count        -O--CK   097   097   000    -    10511
  5 Reallocated_Sector_Ct   PO--CK   100   100   024    -    0
  7 Seek_Error_Rate         POSR--   100   100   047    -    0
  8 Seek_Time_Performance   P-S---   100   100   019    -    0
  9 Power_On_Hours          -O--CK   088   088   000    -    6082
 10 Spin_Retry_Count        PO--C-   100   100   020    -    0
 12 Power_Cycle_Count       -O--CK   099   099   000    -    6452
192 Power-Off_Retract_Count -O--CK   100   100   000    -    2097295
193 Load_Cycle_Count        -O--CK   088   088   000    -    246869
194 Temperature_Celsius     -O---K   100   100   000    -    22 (Min/Max 6/51)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    0
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
198 Offline_Uncorrectable   ----C-   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   253   000    -    0
200 Multi_Zone_Error_Rate   POSR--   100   100   060    -    0
203 Run_Out_Cancel          -O----   100   100   000    -    0
240 Transfer_Error_Rate     -OSRCK   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01       GPL,SL  R/O      1  Summary SMART error log
0x02       GPL,SL  R/O     51  Comprehensive SMART error log
0x03       GPL,SL  R/O     64  Ext. Comprehensive SMART error log
0x06       GPL,SL  R/O      1  SMART self-test log
0x07       GPL,SL  R/O      2  Extended self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL,SL  R/O      1  NCQ Command Error log
0x11       GPL,SL  R/O      1  SATA Phy Event Counters log
0x23       GPL,SL  R/O      1  Delayed sector log [OBS-8]
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa1       GPL,SL  VS       1  Device vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 123
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 123 [122] occurred at disk power-on lifetime: 5931 hours (247 days + 3 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 80 00 00 69 00 08 b8 40 00  Error: ICRC, ABRT 128 sectors at LBA = 0x690008b8 = 1761609912

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 08 00 00 19 67 00 08 38 40 00     01:17:15.956  READ DMA EXT
  25 00 00 08 00 00 19 5f 00 08 38 40 00     01:17:15.928  READ DMA EXT
  25 00 00 08 00 00 19 57 00 08 38 40 00     01:17:15.873  READ DMA EXT
  35 00 00 00 10 00 00 a3 00 07 60 40 00     01:17:15.839  WRITE DMA EXT
  35 00 00 00 10 00 00 8b 00 07 e0 40 00     01:17:15.839  WRITE DMA EXT

Error 122 [121] occurred at disk power-on lifetime: 5930 hours (247 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 50 00 00 d3 00 35 b0 40 00  Error: ICRC, ABRT 80 sectors at LBA = 0xd30035b0 = 3540006320

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 08 00 00 0f d1 00 35 00 40 00     00:24:55.254  READ DMA EXT
  25 00 00 08 00 00 1b be 00 28 30 40 00     00:24:55.200  READ DMA EXT
  25 00 00 08 00 00 17 aa 00 62 d0 40 00     00:24:55.173  READ DMA EXT
  25 00 00 08 00 00 17 a2 00 62 d0 40 00     00:24:55.146  READ DMA EXT
  25 00 00 08 00 00 17 9a 00 62 d0 40 00     00:24:55.119  READ DMA EXT

Error 121 [120] occurred at disk power-on lifetime: 5930 hours (247 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 50 00 00 80 00 5b 18 40 00  Error: ICRC, ABRT 80 sectors at LBA = 0x80005b18 = 2147506968

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 08 00 00 09 7f 00 5b 68 40 00     00:13:41.530  READ DMA EXT
  25 00 00 08 00 00 09 77 00 5b 68 40 00     00:13:41.510  READ DMA EXT
  25 00 00 08 00 00 09 6f 00 5b 68 40 00     00:13:41.489  READ DMA EXT
  25 00 00 08 00 00 09 67 00 5b 68 40 00     00:13:41.469  READ DMA EXT
  25 00 00 08 00 00 09 5f 00 5b 68 40 00     00:13:41.449  READ DMA EXT

Error 120 [119] occurred at disk power-on lifetime: 5930 hours (247 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 40 00 00 9c 00 df f8 40 00  Error: ICRC, ABRT 64 sectors at LBA = 0x9c00dff8 = 2617303032

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 08 00 00 05 96 00 df 38 40 00     00:08:59.938  READ DMA EXT
  25 00 00 08 00 00 05 8e 00 df 38 40 00     00:08:59.918  READ DMA EXT
  25 00 00 08 00 00 05 86 00 df 38 40 00     00:08:59.900  READ DMA EXT
  25 00 00 08 00 00 05 7e 00 df 38 40 00     00:08:59.880  READ DMA EXT
  25 00 00 08 00 00 05 76 00 df 38 40 00     00:08:59.862  READ DMA EXT

Error 119 [118] occurred at disk power-on lifetime: 5930 hours (247 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 d0 00 00 94 00 ca 80 40 00  Error: ICRC, ABRT 208 sectors at LBA = 0x9400ca80 = 2483079808

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 04 e0 00 05 92 00 ca 70 40 00     00:08:49.865  READ DMA EXT
  25 00 00 08 00 00 05 8a 00 ca 70 40 00     00:08:49.843  READ DMA EXT
  25 00 00 08 00 00 05 82 00 ca 70 40 00     00:08:49.822  READ DMA EXT
  25 00 00 08 00 00 05 7a 00 ca 70 40 00     00:08:49.802  READ DMA EXT
  25 00 00 08 00 00 05 72 00 ca 70 40 00     00:08:49.781  READ DMA EXT

Error 118 [117] occurred at disk power-on lifetime: 5930 hours (247 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 a0 00 00 74 00 bf d8 40 00  Error: ICRC, ABRT 160 sectors at LBA = 0x7400bfd8 = 1946206168

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 08 00 00 05 6d 00 bf 78 40 00     00:08:45.636  READ DMA EXT
  25 00 00 08 00 00 05 65 00 bf 78 40 00     00:08:45.625  READ DMA EXT
  25 00 00 08 00 00 05 5d 00 bf 78 40 00     00:08:45.550  READ DMA EXT
  25 00 00 08 00 00 05 55 00 bf 78 40 00     00:08:45.528  READ DMA EXT
  25 00 00 08 00 00 05 4d 00 bf 78 40 00     00:08:45.507  READ DMA EXT

Error 117 [116] occurred at disk power-on lifetime: 5930 hours (247 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 38 00 00 db 00 51 98 40 00  Error: ICRC, ABRT 56 sectors at LBA = 0xdb005198 = 3674231192

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 02 98 00 05 da 00 51 38 40 00     00:08:34.449  READ DMA EXT
  25 00 00 08 00 00 05 d2 00 51 38 40 00     00:08:34.430  READ DMA EXT
  25 00 00 08 00 00 05 ca 00 51 38 40 00     00:08:34.409  READ DMA EXT
  25 00 00 08 00 00 05 c2 00 51 38 40 00     00:08:34.387  READ DMA EXT
  25 00 00 08 00 00 05 ba 00 51 38 40 00     00:08:34.368  READ DMA EXT

Error 116 [115] occurred at disk power-on lifetime: 5930 hours (247 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 50 00 00 98 00 4c e0 40 00  Error: ICRC, ABRT 80 sectors at LBA = 0x98004ce0 = 2550156512

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 06 b0 00 05 93 00 4c 80 40 00     00:08:31.112  READ DMA EXT
  25 00 00 08 00 00 05 8b 00 4c 80 40 00     00:08:31.092  READ DMA EXT
  25 00 00 08 00 00 05 83 00 4c 80 40 00     00:08:31.074  READ DMA EXT
  25 00 00 08 00 00 05 7b 00 4c 80 40 00     00:08:31.054  READ DMA EXT
  25 00 00 08 00 00 05 73 00 4c 80 40 00     00:08:31.036  READ DMA EXT

SMART Extended Self-test Log Version: 1 (2 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Aborted by host               90%      5788         -
# 2  Short offline       Completed without error       00%      5787         -
# 3  Short offline       Completed without error       00%      5755         -
# 4  Short offline       Completed without error       00%      5712         -
# 5  Short offline       Aborted by host               90%      5675         -
# 6  Short offline       Completed without error       00%      5675         -
# 7  Short offline       Aborted by host               90%      5674         -
# 8  Short offline       Aborted by host               90%      5674         -
# 9  Short offline       Aborted by host               90%      5674         -
#10  Short offline       Aborted by host               90%      5674         -
#11  Short offline       Aborted by host               90%      5674         -
#12  Short offline       Aborted by host               90%      5674         -
#13  Short offline       Aborted by host               90%      5674         -
#14  Short offline       Completed without error       00%      5671         -
#15  Short offline       Completed without error       00%      5643         -
#16  Short offline       Aborted by host               90%      5627         -
#17  Short offline       Completed without error       00%      5615         -
#18  Short offline       Completed without error       00%      5581         -
#19  Short offline       Aborted by host               90%      5581         -
#20  Short offline       Aborted by host               90%      5581         -
#21  Short offline       Aborted by host               90%      5581         -
#22  Short offline       Aborted by host               90%      5581         -
#23  Short offline       Aborted by host               90%      5581         -
#24  Short offline       Aborted by host               90%      5580         -
#25  Short offline       Aborted by host               90%      5580         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       0 (0x0000)
Device State:                        Active (0)
Current Temperature:                    22 Celsius
Power Cycle Min/Max Temperature:     20/23 Celsius
Lifetime    Min/Max Temperature:      6/51 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      5/60 Celsius
Min/Max Temperature Limit:           -40/65 Celsius
Temperature History Size (Index):    478 (302)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0002  4            0  R_ERR response for data FIS
0x0003  4            0  R_ERR response for device-to-host data FIS
0x0004  4            0  R_ERR response for host-to-device data FIS
0x0005  4            0  R_ERR response for non-data FIS
0x0006  4            0  R_ERR response for device-to-host non-data FIS
0x0008  4            0  Device-to-host non-data FIS retries
0x0009  4            4  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4            4  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS
0x000f  4            0  R_ERR response for host-to-device data FIS, CRC
0x0010  4            0  R_ERR response for host-to-device data FIS, non-CRC

