smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE-p5 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     MB0500GCEHE
Serial Number:    --
LU WWN Device Id: 5 0014ee ...
Firmware Version: HPG1
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        Not in smartctl database 7.3/5528
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Oct 16 01:08:33 2024 AEDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Unavailable
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 7980) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  81) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x303d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    335
  3 Spin_Up_Time            POS--K   174   171   021    -    2275
  4 Start_Stop_Count        -O--CK   100   100   000    -    457
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         POSR-K   200   200   051    -    0
  9 Power_On_Hours          -O--CK   082   082   000    -    13349
 10 Spin_Retry_Count        PO--CK   100   100   051    -    0
 11 Calibration_Retry_Count PO--CK   100   100   051    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    457
180 Unknown_HDD_Attribute   POSR-K   200   200   100    -    0
184 End-to-End_Error        PO--CK   100   100   097    -    0
187 Reported_Uncorrect      -O--CK   100   001   000    -    234
188 Command_Timeout         -O--CK   100   094   000    -    13
190 Airflow_Temperature_Cel -O---K   064   059   045    -    36
192 Power-Off_Retract_Count -O--CK   200   200   000    -    100
193 Load_Cycle_Count        -O--CK   200   200   000    -    356
194 Temperature_Celsius     -O---K   107   102   000    -    36
195 Hardware_ECC_Recovered  -OS-CK   200   200   000    -    0
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    23
198 Offline_Uncorrectable   ----CK   200   200   000    -    16
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    20
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x04       GPL,SL  R/O      8  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x08       GPL     R/O      2  Power Conditions log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb5  GPL,SL  VS       1  Device vendor specific log
0xb6       GPL     VS    1903  Device vendor specific log
0xb7       GPL,SL  VS       1  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      24  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 234 (device log contains only the most recent 24 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 234 [17] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 3a 13 f5 86 40 00  Error: UNC at LBA = 0x3a13f586 = 974386566

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 a0 00 00 3a 13 f5 80 40 08     15:25:30.105  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:30.101  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     15:25:30.101  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     15:25:30.101  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:30.100  SET FEATURES [Enable SATA feature]

Error 233 [16] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 3a 13 f5 86 40 00  Error: UNC at LBA = 0x3a13f586 = 974386566

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 30 00 00 3a 13 f5 80 40 08     15:25:28.306  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:28.303  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     15:25:28.303  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     15:25:28.302  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:28.302  SET FEATURES [Enable SATA feature]

Error 232 [15] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 3a 13 f5 86 40 00  Error: UNC at LBA = 0x3a13f586 = 974386566

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 98 00 00 3a 13 f5 80 40 08     15:25:26.508  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:26.506  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     15:25:26.504  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     15:25:26.504  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:26.504  SET FEATURES [Enable SATA feature]

Error 231 [14] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 3a 13 f5 86 40 00  Error: UNC at LBA = 0x3a13f586 = 974386566

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 40 00 00 3a 13 f5 80 40 08     15:25:24.717  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:24.716  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     15:25:24.714  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     15:25:24.714  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:24.714  SET FEATURES [Enable SATA feature]

Error 230 [13] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 3a 13 f5 86 40 00  Error: UNC at LBA = 0x3a13f586 = 974386566

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 28 00 00 3a 13 f5 80 40 08     15:25:22.940  READ FPDMA QUEUED
  60 00 08 00 20 00 00 3a 13 f5 78 40 08     15:25:22.940  READ FPDMA QUEUED
  60 00 08 00 18 00 00 3a 13 f5 70 40 08     15:25:22.940  READ FPDMA QUEUED
  60 00 08 00 10 00 00 3a 13 f5 68 40 08     15:25:22.939  READ FPDMA QUEUED
  60 00 08 00 08 00 00 3a 13 f5 60 40 08     15:25:22.939  READ FPDMA QUEUED

Error 229 [12] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 3a 13 f0 fb 40 00  Error: UNC at LBA = 0x3a13f0fb = 974385403

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 18 00 00 3a 13 f0 f8 40 08     15:25:21.090  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:21.087  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     15:25:21.087  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     15:25:21.087  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:21.085  SET FEATURES [Enable SATA feature]

Error 228 [11] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 3a 13 f0 fb 40 00  Error: UNC at LBA = 0x3a13f0fb = 974385403

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 b8 00 00 3a 13 f0 f8 40 08     15:25:19.291  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:19.288  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     15:25:19.288  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     15:25:19.288  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:19.287  SET FEATURES [Enable SATA feature]

Error 227 [10] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 3a 13 f0 fb 40 00  Error: UNC at LBA = 0x3a13f0fb = 974385403

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 00 00 00 3a 13 f0 f8 40 08     15:25:17.493  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:17.490  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     15:25:17.489  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     15:25:17.489  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     15:25:17.489  SET FEATURES [Enable SATA feature]

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       90%     13211         974000030
# 2  Extended offline    Completed: read failure       90%     12324         974000030
# 3  Extended offline    Completed: read failure       90%     12323         974000030
# 4  Extended offline    Completed: read failure       90%     11716         974000030
# 5  Extended offline    Completed: read failure       90%     10478         974000030
# 6  Extended offline    Completed: read failure       90%     10006         974000030
# 7  Extended offline    Completed: read failure       90%      9932         974000030
# 8  Extended offline    Completed: read failure       90%      9932         974000030
# 9  Extended offline    Completed: read failure       90%      9932         974000030
#10  Extended offline    Completed: read failure       90%      9932         974000030
#11  Extended offline    Completed: read failure       90%      9932         974000030
#12  Extended offline    Completed: read failure       90%      9932         974000030
#13  Extended offline    Completed: read failure       90%      9932         974000030
#14  Extended offline    Completed: read failure       90%      9932         974000030
#15  Extended offline    Completed: read failure       90%      9736         973219881
#16  Extended offline    Completed: read failure       90%      9713         973605476
#17  Extended offline    Completed: read failure       90%      9713         974000030
#18  Extended offline    Completed: read failure       90%      9713         973605476

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
Device State:                        Active (0)
Current Temperature:                    36 Celsius
Power Cycle Min/Max Temperature:     35/40 Celsius
Lifetime    Min/Max Temperature:      0/41 Celsius
Specified Max Operating Temperature:    60 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (182)

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP Log 0x04)
Page  Offset Size        Value Flags Description
0x01  =====  =               =  ===  == General Statistics (rev 2) ==
0x01  0x008  4             457  ---  Lifetime Power-On Resets
0x01  0x010  4           13349  ---  Power-on Hours
0x01  0x018  6      9768577735  ---  Logical Sectors Written
0x01  0x020  6       102247492  ---  Number of Write Commands
0x01  0x028  6    931560053863  ---  Logical Sectors Read
0x01  0x030  6      2344225690  ---  Number of Read Commands
0x03  =====  =               =  ===  == Rotating Media Statistics (rev 1) ==
0x03  0x008  4           14000  ---  Spindle Motor Power-on Hours
0x03  0x010  4           13997  ---  Head Flying Hours
0x03  0x018  4             457  ---  Head Load Events
0x03  0x020  4             200  N--  Number of Reallocated Logical Sectors
0x03  0x028  4            1182  ---  Read Recovery Attempts
0x03  0x030  4               0  ---  Number of Mechanical Start Failures
0x04  =====  =               =  ===  == General Errors Statistics (rev 1) ==
0x04  0x008  4             100  N--  Number of Reported Uncorrectable Errors
0x04  0x010  4             100  N--  Resets Between Cmd Acceptance and Completion
0x05  =====  =               =  ===  == Temperature Statistics (rev 1) ==
0x05  0x008  1              36  ---  Current Temperature
0x05  0x010  1              35  ---  Average Short Term Temperature
0x05  0x018  1              28  ---  Average Long Term Temperature
0x05  0x020  1              41  ---  Highest Temperature
0x05  0x028  1              18  ---  Lowest Temperature
0x05  0x030  1              35  ---  Highest Average Short Term Temperature
0x05  0x038  1              21  ---  Lowest Average Short Term Temperature
0x05  0x040  1              33  ---  Highest Average Long Term Temperature
0x05  0x048  1              26  ---  Lowest Average Long Term Temperature
0x05  0x050  4               0  ---  Time in Over-Temperature
0x05  0x058  1              60  ---  Specified Maximum Operating Temperature
0x05  0x060  4               0  ---  Time in Under-Temperature
0x05  0x068  1               0  ---  Specified Minimum Operating Temperature
0x06  =====  =               =  ===  == Transport Statistics (rev 1) ==
0x06  0x008  4            2127  ---  Number of Hardware Resets
0x06  0x010  4            9975  ---  Number of ASR Events
0x06  0x018  4               0  ---  Number of Interface CRC Errors
                                |||_ C monitored condition met
                                ||__ D supports DSN
                                |___ N normalized value

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2           36  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2           18  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4        23897  Vendor specific

