smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F2 EG
Device Model:     SAMSUNG HD103SI
Serial Number:    --
LU WWN Device Id: 5 0024e9 ...
Firmware Version: 1AG01118
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Thu Aug 29 19:21:55 2024 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (  38)	The self-test routine was interrupted
					by the host with a hard or soft reset.
Total time to complete Offline 
data collection: 		(13053) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 218) minutes.
Conveyance self-test routine
recommended polling time: 	 (  23) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   095   051    -    94
  3 Spin_Up_Time            POS---   082   082   011    -    6270
  4 Start_Stop_Count        -O--CK   096   096   000    -    4156
  5 Reallocated_Sector_Ct   PO--CK   100   100   010    -    0
  7 Seek_Error_Rate         POSR--   100   100   051    -    0
  8 Seek_Time_Performance   P-S--K   100   100   015    -    11148
  9 Power_On_Hours          -O--CK   092   092   000    -    38160
 10 Spin_Retry_Count        PO--CK   100   100   051    -    0
 11 Calibration_Retry_Count -O--C-   100   100   000    -    3
 12 Power_Cycle_Count       -O--CK   096   096   000    -    4156
 13 Read_Soft_Error_Rate    -OSR--   100   095   000    -    94
183 Runtime_Bad_Block       -O--CK   100   100   000    -    145
184 End-to-End_Error        PO--CK   100   100   000    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    444
188 Command_Timeout         -O--CK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   072   056   000    -    28 (Min/Max 19/28)
194 Temperature_Celsius     -O---K   066   054   000    -    34 (Min/Max 19/34)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    82195
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
197 Current_Pending_Sector  -O--C-   100   097   000    -    0
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   100   099   000    -    436
200 Multi_Zone_Error_Rate   -O-R--   100   100   000    -    0
201 Soft_Read_Error_Rate    -O-R--   253   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x04       GPL     R/O      2  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x20       GPL     R/O      2  Streaming performance log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 662 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 662 [5] occurred at disk power-on lifetime: 38159 hours (1589 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 4a 00 2f 00 00 00 00 0a d1 40 00   at LBA = 0x00000ad1 = 2769

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 20 20 00 e0 00 00 00 70 66 20 40 00     00:03:07.940  READ FPDMA QUEUED
  60 20 20 00 e0 00 00 00 70 64 20 40 00     00:03:07.940  READ FPDMA QUEUED
  60 20 20 00 e0 00 00 00 00 0a 20 40 00     00:03:07.940  READ FPDMA QUEUED
  60 20 20 00 e0 00 00 00 00 08 20 40 00     00:03:07.940  READ FPDMA QUEUED
  60 20 20 00 01 00 00 00 00 08 00 40 00     00:03:05.710  READ FPDMA QUEUED

Error 661 [4] occurred at disk power-on lifetime: 38107 hours (1587 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 4a 00 57 00 00 00 00 09 a9 40 00   at LBA = 0x000009a9 = 2473

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 f8 00 00 00 00 09 08 40 00     00:00:25.020  READ FPDMA QUEUED
  60 00 00 00 78 00 00 00 00 08 88 40 00     00:00:25.020  READ FPDMA QUEUED
  60 00 00 00 30 00 00 00 00 08 48 40 00     00:00:25.020  READ FPDMA QUEUED
  60 00 00 00 10 00 00 00 00 08 28 40 00     00:00:25.020  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 00 08 10 40 00     00:00:25.020  READ FPDMA QUEUED

Error 660 [3] occurred at disk power-on lifetime: 38107 hours (1587 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 4a 00 5f 00 00 74 70 65 a1 40 00   at LBA = 0x747065a1 = 1953523105

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 02 00 00 00 00 70 64 00 40 00     00:07:41.600  READ FPDMA QUEUED
  60 00 00 01 f8 00 00 00 00 0a 08 40 00     00:07:41.600  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 00 09 f8 40 00     00:07:41.590  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 00 09 f0 40 00     00:07:41.590  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 00 09 e8 40 00     00:07:41.590  READ FPDMA QUEUED

Error 659 [2] occurred at disk power-on lifetime: 38107 hours (1587 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 4a 00 17 00 00 00 00 08 e9 40 00   at LBA = 0x000008e9 = 2281

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 f8 00 00 00 00 09 08 40 00     00:07:40.880  READ FPDMA QUEUED
  60 00 00 00 78 00 00 00 00 08 88 40 00     00:07:40.880  READ FPDMA QUEUED
  60 00 00 00 30 00 00 00 00 08 48 40 00     00:07:40.880  READ FPDMA QUEUED
  60 00 00 00 10 00 00 00 00 08 28 40 00     00:07:40.880  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 00 08 10 40 00     00:07:40.880  READ FPDMA QUEUED

Error 658 [1] occurred at disk power-on lifetime: 38107 hours (1587 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 4a 00 00 00 00 00 00 08 0e 40 00   at LBA = 0x0000080e = 2062

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 00 00 08 08 40 00     00:07:40.160  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 00 08 00 40 00     00:07:40.130  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 70 67 f0 40 00     00:07:40.130  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 70 67 80 40 00     00:07:40.130  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 70 6b f8 40 00     00:07:40.130  READ FPDMA QUEUED

Error 657 [0] occurred at disk power-on lifetime: 38107 hours (1587 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 4a 00 00 00 00 74 70 6a b6 40 00   at LBA = 0x74706ab6 = 1953524406

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 20 00 08 00 00 00 70 6a b0 40 00     00:07:39.480  READ FPDMA QUEUED
  60 20 20 00 08 00 00 00 70 6a a8 40 00     00:07:39.480  READ FPDMA QUEUED
  60 00 20 00 08 00 00 00 70 6a a0 40 00     00:07:39.480  READ FPDMA QUEUED
  60 00 03 00 08 00 00 00 70 6a 98 40 00     00:07:39.480  READ FPDMA QUEUED
  60 00 03 00 08 00 00 00 70 6a 90 40 00     00:07:39.480  READ FPDMA QUEUED

Error 656 [7] occurred at disk power-on lifetime: 38107 hours (1587 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 4a 00 00 00 00 74 70 6a 86 40 00   at LBA = 0x74706a86 = 1953524358

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 03 00 08 00 00 00 70 6a 80 40 00     00:07:38.840  READ FPDMA QUEUED
  60 00 da 00 08 00 00 00 70 6a 78 40 00     00:07:38.840  READ FPDMA QUEUED
  60 00 10 00 08 00 00 00 70 6a 70 40 00     00:07:38.820  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     00:07:38.820  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:07:38.820  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 655 [6] occurred at disk power-on lifetime: 38107 hours (1587 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 4a 00 00 00 00 74 70 6a 76 40 00   at LBA = 0x74706a76 = 1953524342

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 00 70 6a 70 40 00     00:07:38.210  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 70 6a 68 40 00     00:07:38.210  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 70 6a 60 40 00     00:07:38.210  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 70 6a 58 40 00     00:07:38.210  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 70 6a 50 40 00     00:07:38.210  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (2 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Interrupted (host reset)      60%     38156         -
# 2  Short offline       Completed without error       00%     38155         -
# 3  Short offline       Completed without error       00%     38149         -
# 4  Short offline       Completed without error       00%     38127         -
# 5  Short offline       Completed without error       00%     38119         -
# 6  Short offline       Completed without error       00%     38119         -
# 7  Short offline       Interrupted (host reset)      10%     38119         -
# 8  Extended offline    Completed: read failure       80%     38118         281020847
# 9  Extended offline    Interrupted (host reset)      80%     38116         -
#10  Extended offline    Aborted by host               80%     38114         -
#11  Short offline       Completed without error       00%     38112         -
#12  Extended offline    Aborted by host               90%     38112         -
#13  Short offline       Completed without error       00%     38111         -
#14  Extended offline    Aborted by host               90%     38110         -
#15  Extended offline    Completed: read failure       80%     38108         280967369
#16  Short offline       Completed without error       00%     38107         -
#17  Short offline       Completed without error       00%     38105         -
#18  Short offline       Completed without error       00%     38104         -
#19  Extended offline    Completed: read failure       80%     38102         280967369
#20  Extended offline    Aborted by host               80%     38102         -
#21  Short offline       Completed without error       00%     38100         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    34 Celsius
Power Cycle Min/Max Temperature:     --/34 Celsius
Lifetime    Min/Max Temperature:     --/46 Celsius

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (46)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: Input/output error
Read Device Statistics page 0x00 failed

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2           35  Device-to-host register FISes sent due to a COMRESET
0x0001  2            3  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2           35  Transition from drive PhyRdy to drive PhyNRdy
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC



