smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE-p1 amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     SAMSUNG HD161HJ
Serial Number:    --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: JF100-22
User Capacity:    160,041,885,696 bytes [160 GB]
Sector Size:      512 bytes logical/physical
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Thu Dec 17 15:54:52 2020 +08
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is:     128 (quiet), recommended: 254
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Unavailable
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x02)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 2891) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  49) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   253   100   051    -    0
  3 Spin_Up_Time            POS---   253   253   025    -    4480
  4 Start_Stop_Count        -O--CK   096   096   000    -    4370
  5 Reallocated_Sector_Ct   PO--CK   253   253   010    -    0
  7 Seek_Error_Rate         POSR--   253   253   051    -    0
  8 Seek_Time_Performance   P-S--K   253   253   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    3597
 10 Spin_Retry_Count        PO--CK   253   253   051    -    0
 11 Calibration_Retry_Count -O--C-   253   253   000    -    0
 12 Power_Cycle_Count       -O--CK   098   098   000    -    2357
 13 Read_Soft_Error_Rate    -OSR--   100   100   000    -    91769
184 End-to-End_Error        PO--CK   253   253   099    -    0
187 Reported_Uncorrect      -O--CK   253   253   000    -    0
188 Command_Timeout         -O--CK   253   253   000    -    0
190 Airflow_Temperature_Cel -O---K   157   115   000    -    27 (Min/Max 16/41)
194 Temperature_Celsius     -O---K   151   106   000    -    29 (Min/Max 16/44)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    91769
196 Reallocated_Event_Count -O--CK   253   253   000    -    0
197 Current_Pending_Sector  -O--C-   253   253   000    -    0
198 Offline_Uncorrectable   ----CK   253   253   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    1801
200 Multi_Zone_Error_Rate   -O-R--   253   100   000    -    0
201 Soft_Read_Error_Rate    -O-R--   253   100   000    -    0
202 Data_Address_Mark_Errs  -O--CK   253   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 2350 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2350 [5] occurred at disk power-on lifetime: 11372 hours (473 days + 20 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 c0 00 ef 98 c7 00 00 00 ca 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  58 00 00 00 c0 ca 00 00 ef 98 c6 00 00     00:00:00.005  [RESERVED]
  58 00 00 00 c0 ca 00 00 ef 98 c5 00 00     00:00:00.005  [RESERVED]
  58 00 00 00 c0 ca 00 00 ef 98 c4 00 00     00:00:00.005  [RESERVED]
  58 00 00 00 c0 ca 00 00 ef 98 c3 00 00     00:00:00.005  [RESERVED]
  00 00 16 01 8a 00 00 20 c0 00 20 2c a0     00:00:03.559  NOP [Reserved subcommand] [OBS-ACS-2]

Error 2349 [4] occurred at disk power-on lifetime: 11366 hours (473 days + 14 hours)
  When the command that caused the error occurred, the device was in a reserved state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 01 e0 0f bc 00 00 12 35 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  06 01 00 12 00 35 00 00 e0 0f bb 00 00     00:00:00.005  DATA SET MANAGEMENT
  06 01 00 12 00 35 00 00 e0 0f ba 00 00     00:00:00.005  DATA SET MANAGEMENT
  06 01 00 12 00 35 00 00 e0 0f b9 00 00     00:00:00.005  DATA SET MANAGEMENT
  06 01 00 12 00 35 00 00 e0 0f b8 00 00     00:00:00.005  DATA SET MANAGEMENT
  09 11 89 11 91 00 00 11 06 c9 b1 02 11     00:00:00.000  [RESERVED]

Error 2348 [3] occurred at disk power-on lifetime: 25408 hours (1058 days + 16 hours)
  When the command that caused the error occurred, the device was in a reserved state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 00 00 00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 16 01 8d 00 00 20 c0 00 20 2d a1     00:00:03.559  NOP [Reserved subcommand] [OBS-ACS-2]

Error 2347 [2] occurred at disk power-on lifetime: 11372 hours (473 days + 20 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  98 -- c0 ca ef 00 00 7a 00 05 58 00 c6

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  05 00 00 00 00 58 ef c5 ca 98 c0 7a 05 37d+06:47:05.472  [RESERVED]
  c4 ef 98 58 ca 00 00 05 00 00 7a c0 c3 23d+18:10:39.471  READ MULTIPLE
  e7 01 86 20 20 00 00 00 28 c0 00 03 00 37d+06:47:05.472  FLUSH CACHE
  88 00 00 00 84 00 e0 98 51 15 40 a2 04  4d+09:26:35.878  [VENDOR SPECIFIC]
  98 e0 15 45 ca 00 00 04 00 00 e1 40 97 43d+17:50:47.520  CHECK POWER MODE [RET-4]

Error 2346 [1] occurred at disk power-on lifetime: 16384 hours (682 days + 16 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  ca -- 15 e1 45 40 00 00 00 00 04 95 e0  Error: 

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 20 20 00 00 e7 00 00 03 27 c0 0d 01  4d+04:33:57.248  NOP [Reserved subcommand] [OBS-ACS-2]
  66 00 84 8c 40 88 00 e0 a2 51 15 70 00 26d+00:29:12.736  [RESERVED FOR SERIAL ATA]
  e0 06 ca 04 e1 8c 00 00 40 00 00 15 e0     00:05:19.750  STANDBY IMMEDIATE
  00 00 00 8a 40 04 06 e0 e1 ca 15 00 00  4d+04:24:07.424  NOP [Abort queued commands]
  e0 c8 ca 04 e0 89 00 00 40 00 00 15 e0     00:05:19.688  STANDBY IMMEDIATE

Error 2345 [0] occurred at disk power-on lifetime: 5512 hours (229 days + 16 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 2c 15 82 70 a2 51 88 00 e0 66 00  Device Fault 5506 sectors at LBA = 0x70a2578800e0 = 123842555543776

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 04 e0 00 00 e0 82 00 15 40 00 ca 89 25d+15:09:52.516  READ DMA
  00 80 40 e0 15 00 04 89 00 e0 ca 00 00 39d+09:28:03.201  NOP [Reserved subcommand] [OBS-ACS-2]
  89 04 e0 00 00 e0 7f 00 15 40 00 ca 89     00:00:00.004  [VENDOR SPECIFIC]
  00 00 00 00 c0 00 e7 00 0d 03 25 00 20 39d+09:28:03.198  NOP [Abort queued commands]
  a0 29 40 e0 15 66 88 00 70 a2 51 2c 00  6d+05:09:30.752  PACKET

Error 2344 [7] occurred at disk power-on lifetime: 11372 hours (473 days + 20 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 40 00 e0 01 b9 00 00 00 ca 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  db 00 00 00 40 ca 00 00 e0 01 b8 00 00     00:00:00.005  ACKNOWLEDGE MEDIA CHANGE [RET-4]
  db 00 2a 00 69 ca 00 00 e0 00 a1 00 00     00:00:00.005  ACKNOWLEDGE MEDIA CHANGE [RET-4]
  db 00 40 00 29 ca 00 00 e0 00 a1 00 00     00:00:00.005  ACKNOWLEDGE MEDIA CHANGE [RET-4]
  db 00 00 00 c0 ca 00 00 e0 01 b6 00 00     00:00:00.005  ACKNOWLEDGE MEDIA CHANGE [RET-4]
  00 00 16 01 86 00 00 20 c0 00 20 2e a0     00:00:03.559  NOP [Reserved subcommand] [OBS-ACS-2]

Error 2343 [6] occurred at disk power-on lifetime: 11372 hours (473 days + 20 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 00 e3 5e 50 00 00 00 ca 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  64 00 40 00 00 ca 00 00 e3 5c e3 00 00     00:00:00.005  SEND FPDMA QUEUED
  64 00 40 00 c0 c8 00 00 e3 5c e2 00 00     00:00:00.005  SEND FPDMA QUEUED
  26 00 00 00 80 ca 00 00 e9 c9 ed 00 00     00:00:00.005  READ DMA QUEUED EXT [OBS-ACS-2]
  26 00 00 00 40 ca 00 00 e9 c9 ec 00 00     00:00:00.005  READ DMA QUEUED EXT [OBS-ACS-2]
  00 00 16 01 8d 00 00 20 c0 00 20 2d a1     00:00:03.559  NOP [Reserved subcommand] [OBS-ACS-2]

SMART Extended Self-test Log (GP Log 0x07) not supported

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      3502         -
# 2  Short offline       Completed without error       00%         0         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    29 Celsius
Power Cycle Min/Max Temperature:     26/29 Celsius
Lifetime    Min/Max Temperature:     17/51 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (102)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            1  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8001  2            0  Vendor specific

