smartctl 7.3 2022-02-28 r5338 [FreeBSD 12.3-RELEASE-p5 amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint T166
Device Model:     SAMSUNG HD321KJ
Serial Number:    --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: CP100-10
User Capacity:    320,072,933,376 bytes [320 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database 7.3/5319
ATA Version is:   ATA8-ACS T13/1699-D revision 3b
SATA Version is:  SATA 2.5, 3.0 Gb/s
Local Time is:    Fri May 13 21:53:47 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (  25)	The self-test routine was aborted by
					the host.
Total time to complete Offline 
data collection: 		( 5767) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  99) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   253   100   051    -    0
  3 Spin_Up_Time            POS---   100   100   015    -    5632
  4 Start_Stop_Count        -O--CK   082   082   000    -    18417
  5 Reallocated_Sector_Ct   PO--CK   253   253   010    -    0
  7 Seek_Error_Rate         POSR--   253   253   051    -    0
  8 Seek_Time_Performance   P-S--K   253   253   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    25352
 10 Spin_Retry_Count        PO--CK   253   253   051    -    0
 11 Calibration_Retry_Count -O--C-   253   100   000    -    0
 12 Power_Cycle_Count       -O--CK   090   090   000    -    10264
187 Reported_Uncorrect      -O--CK   089   089   000    -    2949132
188 Command_Timeout         -O--CK   253   253   000    -    0
190 Airflow_Temperature_Cel -O---K   062   053   000    -    38
194 Temperature_Celsius     -O---K   124   097   000    -    38
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    17948
196 Reallocated_Event_Count -O--CK   253   253   000    -    0
197 Total_Pending_Sectors   -O--C-   100   100   000    -    1
198 Offline_Uncorrectable   ----CK   253   253   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0
200 Multi_Zone_Error_Rate   -O-R--   253   100   000    -    0
201 Soft_Read_Error_Rate    -O-R--   253   100   000    -    0
202 Data_Address_Mark_Errs  -O--CK   253   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Invalid Error Log index = 0x0000, trying reserved byte (0x08) instead
Device Error Count: 1224 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1224 [7] occurred at disk power-on lifetime: 18692 hours (778 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 02 13 e6 b0 e0 00  Error: UNC 8 sectors at LBA = 0x0213e6b0 = 34858672

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 02 13 e6 b0 e0 00     00:37:29.875  READ DMA EXT
  25 00 00 00 40 00 00 0e d9 56 d8 e0 00     00:37:27.000  READ DMA EXT
  25 00 00 00 40 00 00 0e d9 52 f0 e0 00     00:37:27.000  READ DMA EXT
  35 00 00 00 10 00 00 00 03 4c 28 e0 00     00:37:27.000  WRITE DMA EXT
  35 00 00 00 12 00 00 01 03 e7 65 e0 00     00:37:27.000  WRITE DMA EXT

Error 1223 [6] occurred at disk power-on lifetime: 18692 hours (778 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 20 00 00 02 13 e6 a0 e0 00  Error: UNC 32 sectors at LBA = 0x0213e6a0 = 34858656

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 20 00 00 02 13 e6 a0 e0 00     00:37:25.125  READ DMA EXT
  25 00 00 00 20 00 00 17 8c 2f e0 e0 00     00:37:22.313  READ DMA EXT
  25 00 00 00 80 00 00 0d a8 87 48 e0 00     00:37:22.313  READ DMA EXT
  25 00 00 00 18 00 00 00 1c c1 e8 e0 00     00:37:22.250  READ DMA EXT
  25 00 00 00 80 00 00 00 1c c1 68 e0 00     00:37:22.250  READ DMA EXT

Error 1222 [5] occurred at disk power-on lifetime: 18674 hours (778 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 02 13 e6 b0 e0 00  Error: UNC 8 sectors at LBA = 0x0213e6b0 = 34858672

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 02 13 e6 b0 e0 00     00:49:45.625  READ DMA EXT
  25 00 00 00 08 00 00 00 c4 35 10 e0 00     00:49:42.813  READ DMA EXT
  ea 00 00 00 00 b0 a3 d7 00 00 00 e0 00     00:49:42.750  FLUSH CACHE EXT
  35 00 00 00 08 00 00 17 b0 a3 d0 e0 00     00:49:42.750  WRITE DMA EXT
  25 00 00 00 03 00 00 00 d7 6d d8 e0 00     00:49:42.750  READ DMA EXT

Error 1221 [4] occurred at disk power-on lifetime: 18674 hours (778 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 20 00 00 02 13 e6 a0 e0 00  Error: UNC 32 sectors at LBA = 0x0213e6a0 = 34858656

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 20 00 00 02 13 e6 a0 e0 00     00:49:42.438  READ DMA EXT
  25 00 00 00 08 00 00 00 38 d8 50 e0 00     00:49:39.625  READ DMA EXT
  25 00 00 00 08 00 00 0e f9 6a 00 e0 00     00:49:39.625  READ DMA EXT
  25 00 00 00 80 00 00 08 17 e1 a0 e0 00     00:49:39.563  READ DMA EXT
  35 00 00 00 20 00 00 0f c2 ef e0 e0 00     00:49:39.563  WRITE DMA EXT

Error 1220 [3] occurred at disk power-on lifetime: 18658 hours (777 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 02 13 e6 b0 e0 00  Error: UNC 8 sectors at LBA = 0x0213e6b0 = 34858672

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 02 13 e6 b0 e0 00     02:05:42.313  READ DMA EXT
  25 00 00 00 40 00 00 11 3f 17 20 e0 00     02:05:39.500  READ DMA EXT
  25 00 00 00 08 00 00 0d a8 90 70 e0 00     02:05:39.500  READ DMA EXT
  25 00 00 00 08 00 00 0e 80 87 60 e0 00     02:05:39.500  READ DMA EXT
  25 00 00 00 08 00 00 0e 80 87 58 e0 00     02:05:39.500  READ DMA EXT

Error 1219 [2] occurred at disk power-on lifetime: 18658 hours (777 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 20 00 00 02 13 e6 a0 e0 00  Error: UNC 32 sectors at LBA = 0x0213e6a0 = 34858656

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 20 00 00 02 13 e6 a0 e0 00     02:05:38.750  READ DMA EXT
  25 00 00 00 08 00 00 0e 5a 3f 20 e0 00     02:05:35.938  READ DMA EXT
  25 00 00 00 08 00 00 0f 57 d5 b0 e0 00     02:05:35.938  READ DMA EXT
  25 00 00 00 08 00 00 0e 5a 3f 10 e0 00     02:05:35.938  READ DMA EXT
  25 00 00 00 08 00 00 0e 5a 38 78 e0 00     02:05:35.938  READ DMA EXT

Error 1218 [1] occurred at disk power-on lifetime: 18658 hours (777 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 02 13 e6 b0 e0 00  Error: UNC 8 sectors at LBA = 0x0213e6b0 = 34858672

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 02 13 e6 b0 e0 00     01:39:54.438  READ DMA EXT
  35 00 00 00 10 00 00 18 a3 27 60 e0 00     01:39:51.563  WRITE DMA EXT
  35 00 00 00 20 00 00 0c f6 40 c0 e0 00     01:39:51.563  WRITE DMA EXT
  25 00 00 00 08 00 00 02 13 e6 a8 e0 00     01:39:51.563  READ DMA EXT
  25 00 00 00 08 00 00 14 91 85 60 e0 00     01:39:51.563  READ DMA EXT

Error 1217 [0] occurred at disk power-on lifetime: 18658 hours (777 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 20 00 00 02 13 e6 a0 e0 00  Error: UNC 32 sectors at LBA = 0x0213e6a0 = 34858656

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 20 00 00 02 13 e6 a0 e0 00     01:39:51.250  READ DMA EXT
  25 00 00 00 08 00 00 14 91 85 58 e0 00     01:39:48.375  READ DMA EXT
  25 00 00 00 c0 00 00 14 91 7e d8 e0 00     01:39:48.375  READ DMA EXT
  25 00 00 00 80 00 00 14 91 7e 58 e0 00     01:39:48.375  READ DMA EXT
  25 00 00 00 70 00 00 14 91 7d e8 e0 00     01:39:48.375  READ DMA EXT

SMART Extended Self-test Log (GP Log 0x07) not supported

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       90%     15500         34858675
# 2  Short offline       Completed without error       00%      7772         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    38 Celsius
Power Cycle Min/Max Temperature:     17/38 Celsius
Lifetime    Min/Max Temperature:     10/48 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (117)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            2  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8001  2            0  Vendor specific



