smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE-p4 amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F1 DT
Device Model:     SAMSUNG HD322HJ
Serial Number:    --
LU WWN Device Id: 5 0024e9 ...
Firmware Version: 1AC01118
User Capacity:    320,071,851,520 bytes [320 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Sun Jan  2 18:52:06 2022 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 3991) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  67) minutes.
Conveyance self-test routine
recommended polling time: 	 (   8) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   100   051    -    0
  3 Spin_Up_Time            POS---   092   092   011    -    3240
  4 Start_Stop_Count        -O--CK   097   097   000    -    2948
  5 Reallocated_Sector_Ct   PO--CK   100   100   010    -    0
  7 Seek_Error_Rate         POSR--   100   100   051    -    0
  8 Seek_Time_Performance   P-S--K   100   100   015    -    0
  9 Power_On_Hours          -O--CK   099   099   000    -    7028
 10 Spin_Retry_Count        PO--CK   100   100   051    -    0
 11 Calibration_Retry_Count -O--C-   100   100   000    -    2
 12 Power_Cycle_Count       -O--CK   097   097   000    -    2897
 13 Read_Soft_Error_Rate    -OSR--   100   100   000    -    0
183 Runtime_Bad_Block       -O--CK   100   100   000    -    6
184 End-to-End_Error        PO--CK   001   001   000    -    300
187 Reported_Uncorrect      -O--CK   100   100   000    -    0
188 Command_Timeout         -O--CK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   078   052   000    -    22 (Min/Max 22/22)
194 Temperature_Celsius     -O---K   075   051   000    -    25 (Min/Max 22/25)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    29553
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   099   044   000    -    45614
200 Multi_Zone_Error_Rate   -O-R--   099   081   000    -    662
201 Soft_Read_Error_Rate    -O-R--   253   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x04       GPL     R/O      2  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x20       GPL     R/O      2  Streaming performance log [OBS-8]
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 45631 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 45631 [6] occurred at disk power-on lifetime: 7013 hours (292 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- d0 00 7f 00 00 04 83 23 77 e0 00   127 sectors at LBA = 0x04832377 = 75703159

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 20 20 00 7f 00 00 04 83 23 77 e0 00     00:00:10.870  READ DMA EXT
  25 20 20 00 21 00 00 04 83 23 56 e0 00     00:00:10.870  READ DMA EXT
  25 20 20 00 7f 00 00 04 83 22 d7 e0 00     00:00:10.870  READ DMA EXT
  25 20 20 00 7f 00 00 04 83 22 58 e0 00     00:00:10.860  READ DMA EXT
  25 20 20 00 7f 00 00 04 83 21 d9 e0 00     00:00:10.860  READ DMA EXT

Error 45630 [5] occurred at disk power-on lifetime: 7013 hours (292 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- d0 00 7f 00 00 02 71 46 86 e0 00   127 sectors at LBA = 0x02714686 = 40978054

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 20 20 00 7f 00 00 02 71 47 84 e0 00     00:00:10.220  READ DMA EXT
  25 20 20 00 7f 00 00 02 71 47 05 e0 00     00:00:10.220  READ DMA EXT
  25 20 20 00 7f 00 00 02 71 46 86 e0 00     00:00:10.220  READ DMA EXT
  25 20 20 00 03 00 00 02 71 46 83 e0 00     00:00:10.220  READ DMA EXT
  25 20 20 00 03 00 00 02 71 46 80 e0 00     00:00:10.220  READ DMA EXT

Error 45629 [4] occurred at disk power-on lifetime: 7013 hours (292 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- d0 00 7f 00 00 04 62 16 c8 e0 00   127 sectors at LBA = 0x046216c8 = 73537224

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 20 20 00 7f 00 00 04 62 1b 3f e0 00     00:00:09.880  READ DMA EXT
  25 20 20 00 7f 00 00 04 62 1a c0 e0 00     00:00:09.880  READ DMA EXT
  25 20 20 00 7f 00 00 04 62 1a 41 e0 00     00:00:09.880  READ DMA EXT
  25 20 20 00 7f 00 00 04 62 19 c2 e0 00     00:00:09.880  READ DMA EXT
  25 20 20 00 7f 00 00 04 62 19 43 e0 00     00:00:09.880  READ DMA EXT

Error 45628 [3] occurred at disk power-on lifetime: 6970 hours (290 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 58 00 db 00 00 00 20 53 ad e0 00   219 sectors at LBA = 0x002053ad = 2118573

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  35 00 00 00 ed 00 00 00 20 52 9b e0 00     00:31:32.100  WRITE DMA EXT
  35 00 00 00 ec 00 00 00 20 51 9c e0 00     00:31:32.100  WRITE DMA EXT
  35 00 00 00 ec 00 00 00 20 50 9c e0 00     00:31:32.100  WRITE DMA EXT
  35 00 00 00 f0 00 00 00 20 4f 99 e0 00     00:31:32.100  WRITE DMA EXT
  35 00 00 00 ed 00 00 00 20 4e 9b e0 00     00:31:32.100  WRITE DMA EXT

Error 45627 [2] occurred at disk power-on lifetime: 6969 hours (290 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 58 00 b8 00 00 05 ff 91 f0 e0 00   184 sectors at LBA = 0x05ff91f0 = 100635120

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  35 00 00 00 ee 00 00 05 ff 90 d2 e0 00     00:11:51.970  WRITE DMA EXT
  35 00 00 00 ef 00 00 05 ff 8f d1 e0 00     00:11:51.970  WRITE DMA EXT
  35 00 00 00 ef 00 00 05 ff 8e d1 e0 00     00:11:51.960  WRITE DMA EXT
  35 00 00 00 ee 00 00 05 ff 8d d2 e0 00     00:11:51.960  WRITE DMA EXT
  35 00 00 00 ef 00 00 05 ff 8c d1 e0 00     00:11:51.960  WRITE DMA EXT

Error 45626 [1] occurred at disk power-on lifetime: 6969 hours (290 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 58 00 8b 00 00 05 c5 70 75 e0 00   139 sectors at LBA = 0x05c57075 = 96825461

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  35 00 00 00 ee 00 00 05 c5 6f 33 e0 00     00:01:54.620  WRITE DMA EXT
  35 00 00 00 ee 00 00 05 c5 6e 33 e0 00     00:01:54.620  WRITE DMA EXT
  35 00 00 00 ed 00 00 05 c5 6d 34 e0 00     00:01:54.620  WRITE DMA EXT
  35 00 00 00 ea 00 00 05 c5 6c 37 e0 00     00:01:54.620  WRITE DMA EXT
  35 00 00 00 06 00 00 05 b9 c7 9b e0 00     00:01:54.620  WRITE DMA EXT

Error 45625 [0] occurred at disk power-on lifetime: 6969 hours (290 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 58 00 91 00 00 05 c4 7d 6f e0 00   145 sectors at LBA = 0x05c47d6f = 96763247

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  35 00 00 00 f4 00 00 05 c4 7c 0c e0 00     00:01:50.420  WRITE DMA EXT
  35 00 00 00 ed 00 00 05 c4 7b 13 e0 00     00:01:50.420  WRITE DMA EXT
  35 00 00 00 0e 00 00 0e 00 e8 b2 e0 00     00:01:50.420  WRITE DMA EXT
  35 00 00 00 0f 00 00 0e 00 e8 b1 e0 00     00:01:50.420  WRITE DMA EXT
  35 00 00 00 d0 00 00 0e 05 30 31 e0 00     00:01:50.420  WRITE DMA EXT

Error 45624 [7] occurred at disk power-on lifetime: 6969 hours (290 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- d2 00 01 00 00 05 c2 98 37 e0 00   1 sectors at LBA = 0x05c29837 = 96639031

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  35 00 00 00 ef 00 00 05 c2 96 49 e0 00     00:01:19.210  WRITE DMA EXT
  35 00 00 00 e7 00 00 05 c2 95 51 e0 00     00:01:19.210  WRITE DMA EXT
  35 00 00 00 01 00 00 00 5b d5 e7 e0 00     00:01:19.210  WRITE DMA EXT
  35 00 00 00 07 00 00 00 5d 6e 01 e0 00     00:01:19.210  WRITE DMA EXT
  25 00 00 00 40 00 00 04 4d 8b d8 e0 00     00:01:18.810  READ DMA EXT

SMART Extended Self-test Log Version: 1 (2 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    25 Celsius
Power Cycle Min/Max Temperature:     --/25 Celsius
Lifetime    Min/Max Temperature:     --/50 Celsius

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (75)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: Input/output error
Read Device Statistics page 0x00 failed

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            1  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            1  Transition from drive PhyRdy to drive PhyNRdy
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC

