smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.3-RELEASE amd64] (local build)
Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint T166
Device Model:     SAMSUNG HD501LJ
Serial Number:    --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: CR100-12
User Capacity:    500,106,780,160 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database 7.5/5706
ATA Version is:   ATA8-ACS T13/1699-D revision 3b
SATA Version is:  SATA 2.5, 3.0 Gb/s
Local Time is:    Sat Aug  2 17:52:02 2025 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, NOT FROZEN [SEC1]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 8852) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 151) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   253   100   051    -    0
  3 Spin_Up_Time            POS---   100   100   015    -    7680
  4 Start_Stop_Count        -O--CK   089   089   000    -    11594
  5 Reallocated_Sector_Ct   PO--CK   253   253   010    -    0
  7 Seek_Error_Rate         POSR--   253   253   051    -    0
  8 Seek_Time_Performance   P-S--K   253   253   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    15814
 10 Spin_Retry_Count        PO--CK   253   253   051    -    0
 11 Calibration_Retry_Count -O--C-   253   100   000    -    0
 12 Power_Cycle_Count       -O--CK   095   095   000    -    5226
 13 Read_Soft_Error_Rate    -OSR--   100   100   000    -    2650
187 Reported_Uncorrect      -O--CK   253   253   000    -    0
188 Command_Timeout         -O--CK   100   100   000    -    13
190 Airflow_Temperature_Cel -O---K   075   057   000    -    25
194 Temperature_Celsius     -O---K   154   109   000    -    28
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    2650
196 Reallocated_Event_Count -O--CK   253   253   000    -    0
197 Total_Pending_Sectors   -O--C-   253   253   000    -    0
198 Offline_Uncorrectable   ----CK   253   253   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    3
200 Multi_Zone_Error_Rate   -O-R--   253   100   000    -    0
201 Soft_Read_Error_Rate    -O-R--   253   100   000    -    0
202 Data_Address_Mark_Errs  -O--CK   100   100   000    -    1
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Invalid Error Log index = 0x0000, trying reserved byte (0x05) instead
Device Error Count: 21 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 21 [4] occurred at disk power-on lifetime: 15640 hours (651 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 01 00 00 00 00 00 00 e0 00  Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 01 00 00 00 00 00 00 e0 00     07:14:55.813  READ DMA
  25 93 ff 8e 19 00 00 00 00 8d 01 e0 00     07:14:30.875  READ DMA EXT
  25 c9 ff 8e 10 00 00 00 00 8d 01 e0 00     07:14:30.875  READ DMA EXT
  25 d5 ff 8e 0e 00 00 00 00 08 01 e0 00     07:14:30.875  READ DMA EXT
  25 9b ff 8d ee 00 00 00 00 08 01 e0 00     07:14:30.875  READ DMA EXT

Error 20 [3] occurred at disk power-on lifetime: 15633 hours (651 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 18 c0 00 00 03 e7 cd c0 40 00  Error: ICRC, ABRT at LBA = 0x03e7cdc0 = 65523136

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 60 c0 18 c0 00 00 03 e7 cd c0 40 00     00:40:11.813  WRITE FPDMA QUEUED
  60 80 60 17 b8 00 00 02 7f a2 e0 40 00     00:40:11.813  READ FPDMA QUEUED
  60 c0 80 16 b0 00 00 02 7f a2 40 40 00     00:40:11.813  READ FPDMA QUEUED
  60 90 c0 15 a8 00 00 02 7f a1 60 40 00     00:40:11.813  READ FPDMA QUEUED
  61 20 90 14 a0 00 00 02 7f 9f a0 40 00     00:40:11.813  WRITE FPDMA QUEUED

Error 19 [2] occurred at disk power-on lifetime: 15633 hours (651 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 0c 60 00 00 03 e7 cb 80 40 00  Error: ICRC, ABRT at LBA = 0x03e7cb80 = 65522560

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 20 20 0c 60 00 00 03 e7 cb 80 40 00     00:40:11.563  WRITE FPDMA QUEUED
  60 20 20 0b 58 00 00 03 5c c6 e0 40 00     00:40:11.563  READ FPDMA QUEUED
  61 20 20 0a 50 00 00 03 4d e3 80 40 00     00:40:11.563  WRITE FPDMA QUEUED
  61 20 20 09 48 00 00 03 e7 cb 60 40 00     00:40:11.563  WRITE FPDMA QUEUED
  60 18 20 08 40 00 00 02 47 84 c0 40 00     00:40:11.563  READ FPDMA QUEUED

Error 18 [1] occurred at disk power-on lifetime: 15633 hours (651 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 02 10 00 00 03 e7 bc 40 40 00  Error: ICRC, ABRT at LBA = 0x03e7bc40 = 65518656

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 20 20 02 10 00 00 03 e7 bc 40 40 00     00:40:09.938  WRITE FPDMA QUEUED
  60 10 20 01 08 00 00 02 40 24 e0 40 00     00:40:09.938  READ FPDMA QUEUED
  61 10 10 1f f8 00 00 02 40 1b 60 40 00     00:40:09.938  WRITE FPDMA QUEUED
  60 20 10 1e f0 00 00 03 5c f1 88 40 00     00:40:09.938  READ FPDMA QUEUED
  61 20 20 1d e8 00 00 03 4d e3 60 40 00     00:40:09.938  WRITE FPDMA QUEUED

Error 17 [0] occurred at disk power-on lifetime: 15633 hours (651 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 01 00 00 00 00 00 10 e0 00  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  2f 20 00 00 01 00 00 00 00 00 10 e0 00     00:40:07.938  READ LOG EXT
  61 20 20 03 18 00 00 02 7f 79 f8 40 00     00:40:07.938  WRITE FPDMA QUEUED
  61 20 20 02 10 00 00 03 e7 ab e0 40 00     00:40:07.938  WRITE FPDMA QUEUED
  61 20 20 01 08 00 00 03 4d e3 60 40 00     00:40:07.938  WRITE FPDMA QUEUED
  60 20 20 1f f8 00 00 03 5d 22 c0 40 00     00:40:07.938  READ FPDMA QUEUED

Error 16 [7] occurred at disk power-on lifetime: 15633 hours (651 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 1a d0 00 00 03 e7 9d c0 40 00  Error: ICRC, ABRT at LBA = 0x03e79dc0 = 65510848

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 20 20 1a d0 00 00 03 e7 9d c0 40 00     00:40:06.375  WRITE FPDMA QUEUED
  61 20 20 19 c8 00 00 03 e7 9d a0 40 00     00:40:06.375  WRITE FPDMA QUEUED
  60 20 20 18 c0 00 00 02 7d 26 80 40 00     00:40:06.375  READ FPDMA QUEUED
  60 08 20 17 b8 00 00 03 5d 56 80 40 00     00:40:06.375  READ FPDMA QUEUED
  61 08 08 16 b0 00 00 00 64 f4 50 40 00     00:40:06.375  WRITE FPDMA QUEUED

Error 15 [6] occurred at disk power-on lifetime: 15633 hours (651 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 01 00 00 00 00 00 10 e0 00  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  2f 20 00 00 01 00 00 00 00 00 10 e0 00     00:39:55.375  READ LOG EXT
  61 20 20 14 a0 00 00 02 7f e7 60 40 00     00:39:55.375  WRITE FPDMA QUEUED
  60 18 20 13 98 00 00 03 91 07 00 40 00     00:39:55.375  READ FPDMA QUEUED
  61 20 18 12 90 00 00 02 7f e7 40 40 00     00:39:55.375  WRITE FPDMA QUEUED
  61 10 20 11 88 00 00 03 4d e3 00 40 00     00:39:55.375  WRITE FPDMA QUEUED

Error 14 [5] occurred at disk power-on lifetime: 15633 hours (651 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 13 98 00 00 01 3c 32 40 40 00  Error: ICRC, ABRT at LBA = 0x013c3240 = 20722240

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 02 10 13 98 00 00 01 3c 32 40 40 00     00:09:46.250  WRITE FPDMA QUEUED
  ef 00 02 00 00 00 00 00 00 00 00 a0 00     00:09:45.750  SET FEATURES [Enable write cache]
  ef 16 ff 08 f0 00 00 00 00 00 00 a0 00     00:09:44.250  SET FEATURES [Reserved for CFA]
  ef 00 02 00 00 00 00 00 00 00 00 a0 00     00:09:45.250  SET FEATURES [Enable write cache]
  ef 22 ff 08 ee 00 00 00 00 00 00 a0 00     00:09:43.750  SET FEATURES [Reserved for CFA]

SMART Extended Self-test Log (GP Log 0x07) not supported

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     15234         -
# 2  Short offline       Completed without error       00%     15230         -
# 3  Short offline       Completed without error       00%     15229         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    28 Celsius
Power Cycle Min/Max Temperature:     19/28 Celsius
Lifetime    Min/Max Temperature:      6/49 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (110)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            3  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            3  Device-to-host non-data FIS retries
0x0009  2            6  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2           14  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8001  2            0  Vendor specific



