smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F1 DT
Device Model:     SAMSUNG HD642JJ
Serial Number:    --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: 1AA01110
User Capacity:    640,133,946,880 bytes [640 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Sun Jun 13 07:50:13 2021 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is:     254 (maximum performance), recommended: 254
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 7702) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 129) minutes.
Conveyance self-test routine
recommended polling time: 	 (  14) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   083   051    -    52
  3 Spin_Up_Time            POS---   086   086   011    -    5210
  4 Start_Stop_Count        -O--CK   077   077   000    -    23024
  5 Reallocated_Sector_Ct   PO--CK   090   090   010    -    282
  7 Seek_Error_Rate         POSR--   100   100   051    -    29
  8 Seek_Time_Performance   P-S--K   100   100   015    -    0
  9 Power_On_Hours          -O--CK   093   093   000    -    34237
 10 Spin_Retry_Count        PO--CK   100   100   051    -    0
 11 Calibration_Retry_Count -O--C-   091   091   000    -    6780
 12 Power_Cycle_Count       -O--CK   085   085   000    -    14789
 13 Read_Soft_Error_Rate    -OSR--   100   083   000    -    44
183 Runtime_Bad_Block       -O--CK   100   100   000    -    0
184 End-to-End_Error        PO--CK   100   100   099    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    4847
188 Command_Timeout         -O--CK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   084   062   000    -    16 (Min/Max 16/16)
194 Temperature_Celsius     -O---K   081   059   000    -    19 (Min/Max 16/19)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    120235
196 Reallocated_Event_Count -O--CK   094   094   000    -    249
197 Current_Pending_Sector  -O--C-   100   098   000    -    0
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   100   100   000    -    15
200 Multi_Zone_Error_Rate   -O-R--   100   099   000    -    9
201 Soft_Read_Error_Rate    -O-R--   253   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 4529 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 4529 [0] occurred at disk power-on lifetime: 34235 hours (1426 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 42 00 00 00 00 00 00 02 00 40 00   at LBA = 0x00000200 = 512

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 10 00 00 00 00 02 00 40 00     00:13:02.580  READ FPDMA QUEUED
  60 00 00 00 10 00 00 00 00 00 00 40 00     00:13:02.580  READ FPDMA QUEUED
  60 00 00 00 10 00 00 00 00 00 10 40 00     00:13:02.580  READ FPDMA QUEUED
  60 00 00 00 10 00 00 00 00 00 80 40 00     00:13:02.000  READ FPDMA QUEUED
  60 00 00 00 01 00 00 00 85 7a 6e 40 00     00:13:02.000  READ FPDMA QUEUED

Error 4528 [7] occurred at disk power-on lifetime: 34235 hours (1426 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 09 68 f8 40 00  Error: UNC at LBA = 0x000968f8 = 616696

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 01 60 00 00 00 09 68 20 40 00     00:12:20.150  READ DMA EXT
  25 00 00 00 08 00 00 00 39 67 f8 40 00     00:12:20.150  READ DMA EXT
  25 00 00 00 01 00 00 4a 85 7a 6e 40 00     00:12:20.150  READ DMA EXT
  25 00 00 00 20 00 00 00 00 00 02 40 00     00:12:20.150  READ DMA EXT
  25 00 00 00 01 00 00 00 00 00 01 40 00     00:12:20.150  READ DMA EXT

Error 4527 [6] occurred at disk power-on lifetime: 34233 hours (1426 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 00 0d 8a 40 00  Error: UNC at LBA = 0x00000d8a = 3466

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 08 80 00 00 00 00 0d 50 40 00     00:02:02.900  READ DMA EXT
  ec 00 00 00 00 00 00 00 00 00 00 00 00     00:02:02.870  IDENTIFY DEVICE
  ec 00 00 00 00 00 00 00 00 00 00 00 00     00:01:39.830  IDENTIFY DEVICE
  25 00 00 00 01 00 00 48 85 78 00 40 00     00:01:39.830  READ DMA EXT
  25 00 00 00 01 00 00 48 85 78 00 40 00     00:01:39.830  READ DMA EXT

Error 4526 [5] occurred at disk power-on lifetime: 34220 hours (1425 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 40 00 00 00 00 00 00 00 0f 40 00   at LBA = 0x0000000f = 15

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 10 00 00 00 00 00 00 40 00     00:16:07.700  READ FPDMA QUEUED
  ec 00 00 00 00 00 00 00 00 00 00 00 00     00:16:07.680  IDENTIFY DEVICE
  ef 00 10 00 03 00 00 00 00 00 00 00 00     00:16:07.670  SET FEATURES [Enable SATA feature]
  ef 00 10 00 02 00 00 00 00 00 00 00 00     00:16:07.650  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 00 00     00:16:07.620  IDENTIFY DEVICE

Error 4525 [4] occurred at disk power-on lifetime: 34189 hours (1424 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 00 97 9a 40 00  Error: UNC at LBA = 0x0000979a = 38810

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 09 00 00 00 00 00 97 00 40 00     00:02:55.470  READ DMA EXT
  25 00 00 00 80 00 00 00 00 96 80 40 00     00:02:54.810  READ DMA EXT
  25 00 00 00 40 00 00 00 69 56 40 40 00     00:01:54.210  READ DMA EXT
  25 00 00 00 08 00 00 00 69 56 40 40 00     00:01:54.210  READ DMA EXT

Error 4524 [3] occurred at disk power-on lifetime: 34189 hours (1424 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 69 56 78 40 00  Error: UNC at LBA = 0x00695678 = 6903416

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 40 00 00 00 69 56 40 40 00     00:01:53.280  READ DMA EXT
  25 00 00 00 40 00 00 00 69 56 00 40 00     00:01:52.730  READ DMA EXT
  25 00 00 00 40 00 00 00 69 55 c0 40 00     00:01:51.640  READ DMA EXT
  25 00 00 00 40 00 00 00 69 55 80 40 00     00:01:51.640  READ DMA EXT
  25 00 00 00 40 00 00 00 69 55 40 40 00     00:01:51.640  READ DMA EXT

Error 4523 [2] occurred at disk power-on lifetime: 34170 hours (1423 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 42 00 00 00 00 00 04 18 05 40 00   at LBA = 0x00041805 = 268293

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 02 00 00 00 00 03 fc 22 40 00     00:22:43.190  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 04 18 00 40 00     00:22:43.190  READ FPDMA QUEUED
  60 00 00 01 f8 00 00 00 00 02 2a 40 00     00:22:42.590  READ FPDMA QUEUED
  60 00 00 00 f8 00 00 00 00 01 2a 40 00     00:22:42.590  READ FPDMA QUEUED
  60 00 00 00 78 00 00 00 00 00 aa 40 00     00:22:42.590  READ FPDMA QUEUED

Error 4522 [1] occurred at disk power-on lifetime: 34166 hours (1423 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 42 00 00 00 00 00 06 09 88 40 00   at LBA = 0x00060988 = 395656

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 00 06 09 88 40 00     00:33:50.890  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 04 0a c0 40 00     00:33:50.890  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 04 0a b8 40 00     00:33:50.890  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 04 0a b0 40 00     00:33:50.890  READ FPDMA QUEUED
  60 00 00 00 08 00 00 00 04 09 a0 40 00     00:33:50.890  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 0 (2 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    19 Celsius
Power Cycle Min/Max Temperature:     --/19 Celsius
Lifetime    Min/Max Temperature:     --/45 Celsius

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (77)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            3  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            3  Transition from drive PhyRdy to drive PhyNRdy
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC



