smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F1 RE
Device Model:     SAMSUNG HE103UJ
Serial Number:    --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: 1AA01114
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Tue Jul 30 22:53:03 2024 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(11733) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 196) minutes.
Conveyance self-test routine
recommended polling time: 	 (  21) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   099   051    -    47
  3 Spin_Up_Time            POS---   076   076   011    -    8060
  4 Start_Stop_Count        -O--CK   100   100   000    -    61
  5 Reallocated_Sector_Ct   PO--CK   100   100   010    -    0
  7 Seek_Error_Rate         POSR--   100   100   051    -    0
  8 Seek_Time_Performance   P-S--K   100   100   015    -    0
  9 Power_On_Hours          -O--CK   093   093   000    -    34185
 10 Spin_Retry_Count        PO--CK   100   100   051    -    0
 11 Calibration_Retry_Count -O--C-   100   100   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    55
 13 Read_Soft_Error_Rate    -OSR--   100   099   000    -    0
183 Runtime_Bad_Block       -O--CK   100   100   000    -    0
184 End-to-End_Error        PO--CK   047   047   000    -    53
187 Reported_Uncorrect      -O--CK   100   100   000    -    134
188 Command_Timeout         -O--CK   100   100   000    -    5
190 Airflow_Temperature_Cel -O---K   066   055   000    -    34 (Min/Max 20/35)
194 Temperature_Celsius     -O---K   066   054   000    -    34 (Min/Max 20/37)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    42080
196 Reallocated_Event_Count -O--CK   098   098   000    -    73
197 Current_Pending_Sector  -O--C-   100   099   000    -    0
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   100   099   000    -    575
200 Multi_Zone_Error_Rate   -O-R--   100   099   000    -    7
201 Soft_Read_Error_Rate    -O-R--   253   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x04       GPL     R/O      2  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      2  Write stream error log
0x22       GPL     R/O      2  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 1504 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1504 [7] occurred at disk power-on lifetime: 29022 hours (1209 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  96 -- 51 00 00 00 00 0b d7 7e cd e0 00  Error: ICRC, IDNF, ABRT, NM at LBA = 0x0bd77ecd = 198672077

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 aa 03 01 00 00 00 0b d7 7e cb e0 00  9d+03:35:53.180  READ DMA EXT
  35 aa 03 01 00 00 00 02 83 3f 58 e0 00  9d+03:35:53.070  WRITE DMA EXT
  35 aa 03 00 01 00 00 6f 95 63 9f e0 00  9d+03:35:53.010  WRITE DMA EXT
  35 aa 03 01 00 00 00 02 88 f1 a1 e0 00  9d+03:35:53.010  WRITE DMA EXT
  25 aa 03 01 00 00 00 0b d7 7d cb e0 00  9d+03:35:52.950  READ DMA EXT

Error 1503 [6] occurred at disk power-on lifetime: 29022 hours (1209 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  96 -- 51 00 00 00 00 0b d7 7e cd e0 00  Error: ICRC, IDNF, ABRT, NM at LBA = 0x0bd77ecd = 198672077

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 aa 03 01 00 00 00 0b d7 7e 3a e0 00  9d+03:33:27.900  READ DMA EXT
  35 aa 03 01 00 00 00 02 72 0f 9e e0 00  9d+03:33:27.780  WRITE DMA EXT
  35 aa 03 00 01 00 00 6f 95 60 a2 e0 00  9d+03:33:27.720  WRITE DMA EXT
  35 aa 03 01 00 00 00 02 68 50 54 e0 00  9d+03:33:27.710  WRITE DMA EXT
  25 aa 03 01 00 00 00 0b d7 7d 3a e0 00  9d+03:33:27.650  READ DMA EXT

Error 1502 [5] occurred at disk power-on lifetime: 29022 hours (1209 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  96 -- 51 00 00 00 00 0b d7 7e cd e0 00  Error: ICRC, IDNF, ABRT, NM at LBA = 0x0bd77ecd = 198672077

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 aa 03 01 00 00 00 0b d7 7e c9 e0 00  9d+03:31:39.340  READ DMA EXT
  35 aa 03 00 01 00 00 6f 95 63 90 e0 00  9d+03:31:39.250  WRITE DMA EXT
  35 aa 03 00 d3 00 00 01 f9 f2 cc e0 00  9d+03:31:39.250  WRITE DMA EXT
  35 aa 03 01 00 00 00 01 f2 1d 50 e0 00  9d+03:31:39.240  WRITE DMA EXT
  25 aa 03 01 00 00 00 0b d7 7d c9 e0 00  9d+03:31:39.140  READ DMA EXT

Error 1501 [4] occurred at disk power-on lifetime: 27371 hours (1140 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 42 00 00 00 00 0b d7 7e cc 40 00   at LBA = 0x0bd77ecc = 198672076

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 03 00 80 00 00 00 d7 7e 68 40 00  5d+02:34:43.170  READ FPDMA QUEUED
  ef 00 03 00 46 00 00 00 00 00 00 00 00  5d+02:34:43.160  SET FEATURES [Set transfer mode]
  ef 00 03 00 0c 00 00 00 00 00 00 00 00  5d+02:34:43.150  SET FEATURES [Set transfer mode]
  ef 00 03 00 00 00 00 00 00 00 00 00 00  5d+02:34:43.140  SET FEATURES [Set transfer mode]
  10 00 00 00 00 00 00 00 00 00 00 00 00  5d+02:34:42.920  RECALIBRATE [OBS-4]

Error 1500 [3] occurred at disk power-on lifetime: 27371 hours (1140 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 42 00 00 00 00 0b d7 7e cc 40 00   at LBA = 0x0bd77ecc = 198672076

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 03 00 80 00 00 00 d7 7e 68 40 00  5d+02:34:39.160  READ FPDMA QUEUED
  ef 00 03 00 46 00 00 00 00 00 00 00 00  5d+02:34:39.150  SET FEATURES [Set transfer mode]
  ef 00 03 00 0c 00 00 00 00 00 00 00 00  5d+02:34:39.140  SET FEATURES [Set transfer mode]
  ef 00 03 00 00 00 00 00 00 00 00 00 00  5d+02:34:39.130  SET FEATURES [Set transfer mode]
  10 00 00 00 00 00 00 00 00 00 00 00 00  5d+02:34:38.930  RECALIBRATE [OBS-4]

Error 1499 [2] occurred at disk power-on lifetime: 27371 hours (1140 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 42 00 00 00 00 0b d7 7e cc 40 00   at LBA = 0x0bd77ecc = 198672076

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 03 00 80 00 00 00 d7 7e 68 40 00  5d+02:34:35.120  READ FPDMA QUEUED
  ef 00 03 00 46 00 00 00 00 00 00 00 00  5d+02:34:35.110  SET FEATURES [Set transfer mode]
  ef 00 03 00 0c 00 00 00 00 00 00 00 00  5d+02:34:35.100  SET FEATURES [Set transfer mode]
  ef 00 03 00 00 00 00 00 00 00 00 00 00  5d+02:34:35.090  SET FEATURES [Set transfer mode]
  10 00 00 00 00 00 00 00 00 00 00 00 00  5d+02:34:34.890  RECALIBRATE [OBS-4]

Error 1498 [1] occurred at disk power-on lifetime: 27371 hours (1140 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 42 00 00 00 00 0b d7 7e cc 40 00   at LBA = 0x0bd77ecc = 198672076

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 80 00 00 00 d7 7e 68 40 00  5d+02:34:31.130  READ FPDMA QUEUED
  e7 00 00 00 00 00 00 00 00 00 00 40 00  5d+02:34:30.800  FLUSH CACHE
  34 00 00 00 01 00 00 74 6e 00 01 40 00  5d+02:34:30.790  WRITE SECTORS(S) EXT
  40 00 00 00 01 00 00 00 00 00 00 40 00  5d+02:34:30.670  READ VERIFY SECTOR(S)
  61 00 00 00 08 00 00 00 20 02 d0 40 00  5d+02:21:12.070  WRITE FPDMA QUEUED

Error 1497 [0] occurred at disk power-on lifetime: 27271 hours (1136 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 42 00 00 00 00 0b d7 7e cc 40 00   at LBA = 0x0bd77ecc = 198672076

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 03 00 80 00 00 00 d7 7e 68 40 00     22:12:50.560  READ FPDMA QUEUED
  ef 00 03 00 46 00 00 00 00 00 00 00 00     22:12:50.550  SET FEATURES [Set transfer mode]
  ef 00 03 00 0c 00 00 00 00 00 00 00 00     22:12:50.540  SET FEATURES [Set transfer mode]
  ef 00 03 00 00 00 00 00 00 00 00 00 00     22:12:50.530  SET FEATURES [Set transfer mode]
  10 00 00 00 00 00 00 00 00 00 00 00 00     22:12:50.330  RECALIBRATE [OBS-4]

SMART Extended Self-test Log Version: 1 (2 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    34 Celsius
Power Cycle Min/Max Temperature:     --/36 Celsius
Lifetime    Min/Max Temperature:     --/58 Celsius

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (98)

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: Input/output error
Read Device Statistics page 0x00 failed

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            2  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            2  Transition from drive PhyRdy to drive PhyNRdy
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC

