smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint M7E (AF)
Device Model:     SAMSUNG HM321HI
Serial Number:    --
LU WWN Device Id: 5 0024e9 ...
Firmware Version: 2AJ10001
User Capacity:    320,072,933,376 bytes [320 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database 7.3/5319
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Sun May 14 13:04:31 2023 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is:     254 (maximum performance), recommended: 254
APM level is:     254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 4740) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  79) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   100   100   051    -    3324
  2 Throughput_Performance  -OS--K   252   252   000    -    0
  3 Spin_Up_Time            PO---K   093   086   025    -    2197
  4 Start_Stop_Count        -O--CK   064   064   000    -    36723
  5 Reallocated_Sector_Ct   PO--CK   098   098   010    -    97
  7 Seek_Error_Rate         -OSR-K   252   252   051    -    0
  8 Seek_Time_Performance   --S--K   252   252   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    24275
 10 Spin_Retry_Count        -O--CK   252   252   051    -    0
 11 Calibration_Retry_Count -O--CK   098   098   000    -    2539
 12 Power_Cycle_Count       -O--CK   089   089   000    -    12052
 13 Read_Soft_Error_Rate    -O-RCK   100   100   000    -    0
191 G-Sense_Error_Rate      -O---K   076   076   000    -    246317
192 Power-Off_Retract_Count -O---K   252   252   000    -    0
193 Load_Cycle_Count        -O--CK   042   042   000    -    591938
194 Temperature_Celsius     -O----   064   030   000    -    29 (Min/Max 10/70)
195 Hardware_ECC_Recovered  -O-RCK   100   100   000    -    0
196 Reallocated_Event_Count -O--CK   098   098   000    -    97
197 Current_Pending_Sector  -O--CK   252   100   000    -    0
198 Offline_Uncorrectable   ----CK   252   252   000    -    0
199 UDMA_CRC_Error_Count    -OS-CK   090   090   000    -    5356
200 Multi_Zone_Error_Rate   -O-R-K   001   001   000    -    42965
240 Head_Flying_Hours       -O--CK   100   100   000    -    23532
241 Total_LBAs_Written      -O--CK   095   094   000    -    6843174
242 Total_LBAs_Read         -O--CK   094   089   000    -    9168229
254 Free_Fall_Sensor        -O--CK   100   100   000    -    1
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x08       GPL     R/O      2  Power Conditions log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 8463 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 8463 [6] occurred at disk power-on lifetime: 22405 hours (933 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 54 00 00 00 00 00 00 00 40 00  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 0a 00 00 00 23 7c 4a 00 40 08     00:00:15.992  WRITE FPDMA QUEUED
  60 00 00 00 08 00 00 1b 03 50 70 40 08     00:00:15.994  READ FPDMA QUEUED
  60 00 00 00 08 00 00 0a 62 30 c8 40 08     00:00:15.994  READ FPDMA QUEUED
  61 00 00 00 90 00 00 04 84 4f 00 40 08     00:00:15.994  WRITE FPDMA QUEUED
  61 00 00 05 40 00 00 04 84 49 c0 40 08     00:00:15.994  WRITE FPDMA QUEUED

Error 8462 [5] occurred at disk power-on lifetime: 20613 hours (858 days + 21 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 63 c8 00 00 00 00 00 00 40 00  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 30 00 00 19 0d 63 a8 40 08     00:00:00.011  READ FPDMA QUEUED
  60 00 00 00 88 00 00 1c cd e6 78 40 08     00:00:00.018  READ FPDMA QUEUED
  60 00 00 00 08 00 00 24 84 2a a8 40 08     00:00:00.018  READ FPDMA QUEUED
  60 00 00 00 40 00 00 1c cd e4 20 40 00     00:00:00.018  READ FPDMA QUEUED
  60 00 00 00 08 00 00 18 3e ed 58 40 00     00:00:00.018  READ FPDMA QUEUED

Error 8461 [4] occurred at disk power-on lifetime: 20325 hours (846 days + 21 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 34 28 00 00 00 00 00 00 40 00  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 20 00 00 1b 42 34 e8 40 08     00:00:00.010  READ FPDMA QUEUED
  60 00 00 01 00 00 00 1b 42 34 08 40 08     00:00:00.017  READ FPDMA QUEUED
  60 00 00 00 08 00 00 1b 43 2a 90 40 08     00:00:00.017  READ FPDMA QUEUED
  60 00 00 00 08 00 00 1b 43 27 d8 40 08     00:00:00.017  READ FPDMA QUEUED
  60 00 00 00 08 00 00 1b 43 2a a0 40 08     00:00:00.017  READ FPDMA QUEUED

Error 8460 [3] occurred at disk power-on lifetime: 18950 hours (789 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 da e8 00 00 00 00 00 00 e0 00  Error: ICRC, ABRT 56040 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  35 00 00 00 60 00 00 1f 6e da 88 e0 00     00:00:00.353  WRITE DMA EXT
  00 00 00 00 01 00 00 00 00 00 01 40 00     00:00:00.352  NOP [Abort queued commands]
  00 00 00 00 01 00 00 00 00 00 01 40 00     00:00:00.352  NOP [Abort queued commands]
  35 00 00 00 08 00 00 21 6f f8 18 e0 08     00:00:00.351  WRITE DMA EXT
  35 00 00 00 08 00 00 20 ed ed 40 e0 08     00:00:00.351  WRITE DMA EXT

Error 8459 [2] occurred at disk power-on lifetime: 18423 hours (767 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 4a d0 00 00 00 00 00 00 e0 00  Error: ICRC, ABRT 19152 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 98 00 00 00 8f 4a 38 e0 00     00:00:57.219  READ DMA EXT
  25 00 00 00 98 00 00 00 8f 4d d0 e0 00     00:00:57.219  READ DMA EXT
  25 00 00 00 90 00 00 06 8b 15 d0 e0 00     00:00:57.219  READ DMA EXT
  25 00 00 00 08 00 00 06 8b 14 c8 e0 00     00:00:57.219  READ DMA EXT
  25 00 00 00 10 00 00 06 8b 15 c0 e0 00     00:00:57.219  READ DMA EXT

Error 8458 [1] occurred at disk power-on lifetime: 18194 hours (758 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 40 c8 00 00 00 00 00 00 40 00  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 05 40 00 00 25 0a 3b 88 40 08     00:00:01.098  WRITE FPDMA QUEUED
  61 00 00 05 40 00 00 25 0a 3b 88 40 08     00:00:01.099  WRITE FPDMA QUEUED
  61 00 00 05 40 00 00 25 0a 36 48 40 08     00:00:01.099  WRITE FPDMA QUEUED
  61 00 00 05 40 00 00 25 0a 31 08 40 08     00:00:01.099  WRITE FPDMA QUEUED
  61 00 00 05 40 00 00 25 0a 2b c8 40 08     00:00:01.099  WRITE FPDMA QUEUED

Error 8457 [0] occurred at disk power-on lifetime: 18161 hours (756 days + 17 hours)
  When the command that caused the error occurred, the device was in a reserved state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 00 00 00 00 00 00 00 a0 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ec 00 00 00 00 00 00 00 00 00 00 a0 00     00:00:00.330  IDENTIFY DEVICE
  00 00 00 00 01 00 00 00 00 00 01 40 00     00:00:00.330  NOP [Abort queued commands]
  00 00 00 00 01 00 00 00 00 00 01 40 00     00:00:00.330  NOP [Abort queued commands]
  00 00 00 00 01 00 00 00 00 00 01 40 08     00:00:00.324  NOP [Abort queued commands]
  00 00 00 00 01 00 00 00 00 00 01 40 00     00:00:00.323  NOP [Abort queued commands]

Error 8456 [7] occurred at disk power-on lifetime: 11712 hours (488 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 c0 00 00 02 83 2c 60 40 00  Error: UNC at LBA = 0x02832c60 = 42151008

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 e0 00 00 02 83 2c 40 40 00     00:00:08.616  READ FPDMA QUEUED
  60 00 90 00 e0 00 00 02 83 2c 40 40 00     00:00:08.629  READ FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00     00:00:08.628  SET FEATURES [Disable SATA feature]
  ef 00 02 00 00 00 00 00 00 00 00 a0 00     00:00:08.628  SET FEATURES [Enable write cache]
  00 00 00 00 20 00 00 07 8b 7b 60 40 00     00:00:08.628  NOP [Abort queued commands]

SMART Extended Self-test Log Version: 1 (2 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     23661         -
# 2  Short offline       Completed without error       00%     23635         -
# 3  Short offline       Completed without error       00%     23611         -
# 4  Short offline       Completed without error       00%     23605         -
# 5  Short offline       Completed without error       00%     15351         -
# 6  Short offline       Completed without error       00%     14921         -
# 7  Short offline       Completed without error       00%         0         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed [00% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    29 Celsius
Power Cycle Min/Max Temperature:     26/29 Celsius
Lifetime    Min/Max Temperature:     16/70 Celsius
Specified Max Operating Temperature:    80 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         5 minutes
Temperature Logging Interval:        5 minutes
Min/Max recommended Temperature:     -5/80 Celsius
Min/Max Temperature Limit:           -10/85 Celsius
Temperature History Size (Index):    128 (30)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0002  4            0  R_ERR response for data FIS
0x0003  4            0  R_ERR response for device-to-host data FIS
0x0004  4            0  R_ERR response for host-to-device data FIS
0x0005  4            0  R_ERR response for non-data FIS
0x0006  4            0  R_ERR response for device-to-host non-data FIS
0x0007  4            0  R_ERR response for host-to-device non-data FIS
0x0008  4            0  Device-to-host non-data FIS retries
0x0009  4         1608  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4            7  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS
0x000f  4            0  R_ERR response for host-to-device data FIS, CRC
0x0010  4            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  4            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  4            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00  4            0  Vendor specific
0x8e01  4            0  Vendor specific
0x8e02  4            0  Vendor specific
0x8e03  4            0  Vendor specific
0x8e04  4            0  Vendor specific
0x8e05  4            0  Vendor specific
0x8e06  4            0  Vendor specific
0x8e07  4            0  Vendor specific
0x8e08  4            0  Vendor specific
0x8e09  4            0  Vendor specific
0x8e0a  4            0  Vendor specific
0x8e0b  4            0  Vendor specific
0x8e0c  4            0  Vendor specific
0x8e0d  4            0  Vendor specific
0x8e0e  4            0  Vendor specific
0x8e0f  4            0  Vendor specific
0x8e10  4            0  Vendor specific
0x8e11  4            0  Vendor specific



