smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     SAMSUNG HS08XJC
Serial Number:    --
Firmware Version: GR100-05
User Capacity:    80,026,361,856 bytes [80.0 GB]
Sector Size:      512 bytes logical/physical
Device is:        Not in smartctl database 7.3/5319
ATA Version is:   ATA/ATAPI-7, ATA/ATAPI-6 T13/1410D revision 1
Local Time is:    Sat Mar 11 22:04:45 2023 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is:     128 (quiet), recommended: 254
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x59) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  55) minutes.

SMART Attributes Data Structure revision number: 4
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   100   051    -    0
  3 Spin_Up_Time            POS---   095   091   025    -    1792
  4 Start_Stop_Count        -O--CK   100   100   000    -    2777
  5 Reallocated_Sector_Ct   PO--CK   252   252   010    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    174
 12 Power_Cycle_Count       -O--CK   100   100   000    -    55
191 G-Sense_Error_Rate      -O--CK   100   100   000    -    1005
192 Power-Off_Retract_Count -O--CK   100   100   000    -    230
194 Temperature_Celsius     -O---K   151   118   000    -    29 (Min/Max 15/40)
196 Reallocated_Event_Count -O--CK   100   100   000    -    169
197 Current_Pending_Sector  -O--CK   094   094   000    -    16926260
198 Offline_Uncorrectable   -O--CK   099   099   000    -    3037498
199 UDMA_CRC_Error_Count    -O--CK   100   100   000    -    1259577
200 Multi_Zone_Error_Rate   -O--CK   100   100   000    -    1653772
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x80       GPL,SL  R/W     16  Host vendor specific log
0xbb       GPL,SL  VS       4  Device vendor specific log
0xbc       GPL,SL  VS       2  Device vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 158 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 158 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 08 00 00 00 b0 42 f8 e0 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 02     00:00:25.986  NOP [Abort queued commands]
  c8 00 00 00 08 00 00 00 b0 42 f8 e0 00     00:00:23.899  READ DMA
  c8 00 00 00 08 00 00 00 af fe 90 e0 00     00:00:23.463  READ DMA
  c8 00 00 00 40 00 00 00 0b 8d 88 e1 00     00:00:23.346  READ DMA
  c8 00 00 00 08 00 00 00 ae f8 e0 e0 00     00:00:23.321  READ DMA

Error 157 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 00 00 00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:00:01.792  NOP [Abort queued commands]
  ca 00 00 00 08 00 00 00 b0 43 d8 e0 00     00:17:27.059  WRITE DMA
  ca 00 00 00 08 00 00 00 88 f0 50 e0 00     00:17:27.059  WRITE DMA
  ca 00 00 00 18 00 00 00 68 91 c0 e0 00     00:17:27.057  WRITE DMA
  ca 00 00 00 08 00 00 00 68 91 a8 e0 00     00:17:27.056  WRITE DMA

Error 156 [3] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 40 00 00 00 28 45 c0 e0 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 0a     02:28:39.811  NOP [Abort queued commands]
  c8 00 00 00 40 00 00 00 28 45 c0 e0 00     02:28:36.059  READ DMA
  c8 00 00 00 40 00 00 00 28 45 80 e0 00     02:28:36.058  READ DMA
  c8 00 00 00 40 00 00 00 28 45 40 e0 00     02:28:36.056  READ DMA
  c8 00 00 00 40 00 00 00 28 45 00 e0 00     02:28:36.055  READ DMA

Error 155 [2] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 00 00 00 00 14 f6 3f a0 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     02:28:05.045  NOP [Abort queued commands]
  e7 00 00 00 00 00 00 00 14 f6 3f a0 08     02:28:04.125  FLUSH CACHE
  c8 00 00 00 20 00 00 00 14 f6 20 e1 08     02:28:04.078  READ DMA
  c8 00 00 00 08 00 00 00 56 c2 f0 e0 08     02:28:04.058  READ DMA
  c8 00 00 00 08 00 00 00 a4 f7 88 e0 08     02:28:04.040  READ DMA

Error 154 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 40 00 00 00 28 45 c0 e0 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 0a     00:00:36.249  NOP [Abort queued commands]
  c8 00 00 00 40 00 00 00 28 45 c0 e0 00     00:00:32.495  READ DMA
  c8 00 00 00 40 00 00 00 28 45 80 e0 00     00:00:32.494  READ DMA
  c8 00 00 00 40 00 00 00 28 45 40 e0 00     00:00:32.492  READ DMA
  c8 00 00 00 40 00 00 00 28 45 00 e0 00     00:00:32.491  READ DMA

Error 153 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 00 00 00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:00:02.298  NOP [Abort queued commands]
  c8 00 00 00 08 00 00 00 60 f9 00 e4 08     00:04:14.759  READ DMA
  c8 00 00 00 08 00 00 00 61 0a 30 e4 08     00:04:14.754  READ DMA
  c8 00 00 00 08 00 00 00 61 0d 90 e4 08     00:04:14.745  READ DMA
  c8 00 00 00 08 00 00 00 61 09 e8 e4 08     00:04:14.728  READ DMA

Error 152 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 40 00 00 00 c9 2b 00 e5 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 0a     00:00:50.724  NOP [Abort queued commands]
  c8 00 00 00 40 00 00 00 c9 2b 00 e5 00     00:00:48.673  READ DMA
  c8 00 00 00 40 00 00 00 c9 2a c0 e5 00     00:00:48.672  READ DMA
  c8 00 00 00 40 00 00 00 c9 2a 80 e5 00     00:00:48.671  READ DMA
  c8 00 00 00 40 00 00 00 c9 2a 40 e5 00     00:00:48.670  READ DMA

Error 151 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 00 00 00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:00:02.325  NOP [Abort queued commands]
  73 7f ff 7f ee 7f ff 2f af 7c 7f fb 3d 49d+12:23:01.299  SEEK [RET-4]
  fb f5 ff ef dd e7 ff fb f5 bf b7 ff fe 12d+07:55:49.023  [VENDOR SPECIFIC]
  ff ff bd cf eb ff fc 5e b3 de 7e d9 fe 49d+07:43:32.863  [VENDOR SPECIFIC]
  fe ee ff cf bb df ff fb ff ff db fb 7e 49d+16:27:29.407  [VENDOR SPECIFIC]

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11) not supported

