smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     SAMSUNG HS082HB
Serial Number:    --
Firmware Version: NL101-06
User Capacity:    80,026,361,856 bytes [80.0 GB]
Sector Size:      512 bytes logical/physical
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ATA/ATAPI-7, ATA/ATAPI-6 T13/1410D revision 1
Local Time is:    Tue Dec  7 04:42:51 2021 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x59) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  46) minutes.

SMART Attributes Data Structure revision number: 4
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   091   090   051    -    8402
  3 Spin_Up_Time            POS---   094   093   000    -    1973
  4 Start_Stop_Count        -O--CK   088   088   000    -    12354
  5 Reallocated_Sector_Ct   PO--CK   098   098   010    -    13
  7 Seek_Error_Rate         -OSR--   099   099   000    -    10
  8 Seek_Time_Performance   --S--K   252   252   000    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    6567
 10 Spin_Retry_Count        -O--CK   252   252   000    -    0
 12 Power_Cycle_Count       -O--CK   096   096   000    -    4408
191 G-Sense_Error_Rate      -O--CK   001   001   000    -    2355444
192 Power-Off_Retract_Count -O--CK   089   089   000    -    11425
194 Temperature_Celsius     -O---K   151   103   000    -    29 (Min/Max 0/45)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    14257647359
196 Reallocated_Event_Count -O--CK   098   098   000    -    13
197 Current_Pending_Sector  -O--C-   252   098   000    -    0
198 Offline_Uncorrectable   ----CK   252   252   000    -    0
199 UDMA_CRC_Error_Count    -OS-CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   -O-R--   099   099   000    -    463
201 Soft_Read_Error_Rate    -O--CK   252   252   000    -    0
223 Load_Retry_Count        -O--CK   094   094   000    -    7015
225 Load_Cycle_Count        -O--CK   082   082   000    -    185242
255 Unknown_Attribute       -O-R--   001   001   000    -    8690
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x80       GPL,SL  R/W     16  Host vendor specific log
0xbb       GPL,SL  VS       4  Device vendor specific log
0xbc       GPL,SL  VS       2  Device vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 24014 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 24014 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 21 00 00 00 3d 99 68 e9 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 02     00:04:32.312  NOP [Abort queued commands]
  c8 00 00 00 21 00 00 00 3d 99 68 e9 00     00:01:38.682  READ DMA
  c8 00 00 00 00 00 00 00 50 f5 88 e9 00     00:01:38.672  READ DMA
  c8 00 00 00 00 00 00 00 50 f3 88 e9 00     00:01:38.645  READ DMA
  c8 00 00 00 20 00 00 00 3d 9c 88 e9 00     00:01:38.640  READ DMA

Error 24013 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 40 00 00 00 00 0b c8 e0 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:01:03.901  NOP [Abort queued commands]
  c8 00 00 00 40 00 00 00 00 0b c8 e0 00     00:00:55.490  READ DMA
  c8 00 00 00 40 00 00 00 00 07 c8 e0 00     00:00:55.488  READ DMA
  c8 00 00 00 88 00 00 00 3d 99 68 e9 00     00:00:54.376  READ DMA
  c8 00 00 00 88 00 00 00 06 40 28 e0 00     00:00:54.374  READ DMA

Error 24012 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 00 00 00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:00:01.973  NOP [Abort queued commands]
  ca 00 00 00 01 00 00 00 06 52 c8 40 00     00:27:54.848  WRITE DMA
  ca 00 00 00 10 00 00 00 38 ba 78 40 00     00:27:54.846  WRITE DMA
  ca 00 00 00 10 20 00 00 33 5f 58 40 00     00:27:54.844  WRITE DMA
  ca 00 00 00 10 00 00 00 31 ce 38 40 00     00:27:54.843  WRITE DMA

Error 24011 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 01 00 00 00 06 40 2a e0 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:02:42.104  NOP [Abort queued commands]
  c8 00 00 00 01 00 00 00 06 40 2a e0 00     00:02:41.169  READ DMA
  c8 00 00 00 08 00 00 00 b9 f7 30 e1 00     00:02:40.517  READ DMA
  c8 00 00 00 08 00 00 00 b9 f7 28 e1 00     00:02:40.517  READ DMA
  c8 00 00 00 40 00 00 00 b9 f6 e8 e1 00     00:02:40.516  READ DMA

Error 24010 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 08 00 00 00 4b 9d 18 e9 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:01:34.912  NOP [Abort queued commands]
  c8 00 00 00 08 00 00 00 4b 9d 18 e9 00     00:00:41.523  READ DMA
  c8 00 00 00 10 00 00 00 2d 9f 38 e0 00     00:00:41.031  READ DMA
  c8 00 00 00 10 00 00 00 3c a6 f8 e0 00     00:00:41.012  READ DMA
  c8 00 00 00 40 00 00 00 00 02 88 e0 00     00:00:41.005  READ DMA

Error 24009 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 00 00 00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:00:01.904  NOP [Abort queued commands]
  ca 00 00 00 10 00 00 00 2c fa d8 40 00     01:16:37.909  WRITE DMA
  ca 00 00 00 10 00 00 00 2c f2 f8 40 00     01:16:37.909  WRITE DMA
  ca 00 00 00 10 00 00 00 2c f2 c8 40 00     01:16:37.909  WRITE DMA
  ca 00 00 00 08 00 00 00 0d ba c8 40 00     01:16:37.908  WRITE DMA

Error 24008 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 50 00 01 00 00 00 06 40 2a e0 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:00:43.426  NOP [Abort queued commands]
  c8 00 00 00 01 00 00 00 06 40 2a e0 00     00:00:42.511  READ DMA
  c8 00 00 00 08 00 00 00 b9 f7 30 e1 00     00:00:41.855  READ DMA
  c8 00 00 00 08 00 00 00 b9 f7 28 e1 00     00:00:41.855  READ DMA
  c8 00 00 00 40 00 00 00 b9 f6 e8 e1 00     00:00:41.854  READ DMA

Error 24007 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  00 -- 00 00 00 00 00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 01 00 00 00 00 00 01 a0 00     00:00:01.989  NOP [Abort queued commands]
  c8 00 00 00 10 00 00 00 3d db 68 e9 00     00:13:29.943  READ DMA
  c8 00 00 00 10 00 00 00 3d 99 68 e9 00     00:13:29.942  READ DMA
  c8 00 10 00 10 20 00 00 3d 99 78 e9 00     00:13:29.942  READ DMA
  c8 00 00 00 10 00 00 00 3d 99 e8 e9 00     00:13:29.942  READ DMA

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11) not supported

