smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p2 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.12
Device Model:     ST31000524AS
Serial Number:    --
LU WWN Device Id: 5 000c50 ...
Firmware Version: HP63
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Fri Aug 25 22:55:16 2023 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Unknown

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  600) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 167) minutes.
SCT capabilities: 	       (0x103b)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   096   095   006    -    179331727
  3 Spin_Up_Time            PO---K   100   100   000    -    0
  4 Start_Stop_Count        -O--CK   094   094   020    -    6541
  5 Reallocated_Sector_Ct   PO--CK   086   086   036    -    611
  7 Seek_Error_Rate         POSR-K   090   060   030    -    990901854
  9 Power_On_Hours          -O--CK   040   040   000    -    53189
 10 Spin_Retry_Count        PO--CK   100   100   097    -    0
 12 Power_Cycle_Count       -O--CK   094   094   020    -    6540
180 Unknown_HDD_Attribute   PO-R-K   100   100   000    -    3970191066
183 Runtime_Bad_Block       -O--CK   097   097   000    -    3
184 End-to-End_Error        PO--CK   100   100   097    -    0
187 Reported_Uncorrect      -O--CK   001   001   000    -    180
188 Command_Timeout         -O--CK   100   075   000    -    21475295282
189 High_Fly_Writes         -O-RCK   097   097   000    -    3
190 Airflow_Temperature_Cel -O---K   070   062   045    -    30 (Min/Max 29/33)
194 Temperature_Celsius     -O---K   030   040   000    -    30 (0 10 0 0 0)
195 Hardware_ECC_Recovered  -O-RCK   022   018   000    -    179331727
196 Reallocated_Event_Count -O--CK   086   086   036    -    611
197 Current_Pending_Sector  -O--CK   085   085   000    -    648
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01       GPL,SL  R/O      1  Summary SMART error log
0x02       GPL,SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      5  Ext. Comprehensive SMART error log
0x06       GPL,SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa1       GPL,SL  VS      20  Device vendor specific log
0xa2       GPL     VS    2248  Device vendor specific log
0xa8       GPL,SL  VS     129  Device vendor specific log
0xa9       GPL,SL  VS       1  Device vendor specific log
0xb0       GPL     VS    2928  Device vendor specific log
0xbd       GPL     VS     252  Device vendor specific log
0xbe-0xbf  GPL     VS   65535  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 171 (device log contains only the most recent 20 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 171 [10] occurred at disk power-on lifetime: 53155 hours (2214 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 26 d0 9d ee 00 00  Error: UNC at LBA = 0x26d09dee = 651206126

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 40 00 00 22 a6 0e 28 40 00     00:20:10.261  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 0e 68 40 00     00:20:10.260  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 0e a8 40 00     00:20:10.257  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 0e e8 40 00     00:20:10.253  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 0f 28 40 00     00:20:10.252  READ FPDMA QUEUED

Error 170 [9] occurred at disk power-on lifetime: 53155 hours (2214 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 26 d0 9d ee 00 00  Error: UNC at LBA = 0x26d09dee = 651206126

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 40 00 00 22 a6 10 28 40 00     00:20:07.217  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 10 68 40 00     00:20:07.217  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 10 a8 40 00     00:20:07.217  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 10 e8 40 00     00:20:07.217  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 11 28 40 00     00:20:07.214  READ FPDMA QUEUED

Error 169 [8] occurred at disk power-on lifetime: 53155 hours (2214 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 26 d0 9d ee 00 00  Error: UNC at LBA = 0x26d09dee = 651206126

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 40 00 00 41 fe 92 28 40 00     00:20:04.196  READ FPDMA QUEUED
  60 00 00 00 40 00 00 42 0a 7d e8 40 00     00:20:04.195  READ FPDMA QUEUED
  60 00 00 02 40 00 00 26 d0 9d e8 40 00     00:20:04.195  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 00 00     00:20:04.081  READ LOG EXT
  60 00 00 00 40 00 00 41 fe 92 28 40 00     00:20:01.312  READ FPDMA QUEUED

Error 168 [7] occurred at disk power-on lifetime: 53155 hours (2214 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 26 d0 9d ee 00 00  Error: UNC at LBA = 0x26d09dee = 651206126

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 40 00 00 41 fe 92 28 40 00     00:20:01.312  READ FPDMA QUEUED
  60 00 00 00 40 00 00 42 0a 7d e8 40 00     00:20:01.312  READ FPDMA QUEUED
  60 00 00 02 40 00 00 26 d0 9d e8 40 00     00:20:01.311  READ FPDMA QUEUED
  ef 00 02 00 00 00 00 00 00 00 00 40 00     00:20:01.311  SET FEATURES [Enable write cache]
  ef 00 aa 00 00 00 00 00 00 00 00 40 00     00:20:01.310  SET FEATURES [Enable read look-ahead]

Error 167 [6] occurred at disk power-on lifetime: 53155 hours (2214 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 26 d0 9d ee 00 00  Error: UNC at LBA = 0x26d09dee = 651206126

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 40 00 00 22 a6 14 a8 40 00     00:19:58.242  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 14 e8 40 00     00:19:58.234  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 15 28 40 00     00:19:58.227  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 15 68 40 00     00:19:58.227  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 15 a8 40 00     00:19:58.226  READ FPDMA QUEUED

Error 166 [5] occurred at disk power-on lifetime: 53155 hours (2214 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 26 d0 9d ee 00 00  Error: UNC at LBA = 0x26d09dee = 651206126

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 40 00 00 42 0a 7d e8 40 00     00:19:55.223  READ FPDMA QUEUED
  60 00 00 02 40 00 00 26 d0 9d e8 40 00     00:19:55.209  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 15 e8 40 00     00:19:55.204  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 16 28 40 00     00:19:55.204  READ FPDMA QUEUED
  60 00 00 00 40 00 00 22 a6 16 68 40 00     00:19:55.204  READ FPDMA QUEUED

Error 165 [4] occurred at disk power-on lifetime: 53155 hours (2214 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 26 d0 9d ee 00 00  Error: UNC at LBA = 0x26d09dee = 651206126

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 02 40 00 00 26 d0 9d e8 40 00     00:19:52.201  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 00 00     00:19:52.191  READ LOG EXT
  60 00 00 08 00 00 00 28 91 cd 68 40 00     00:19:49.385  READ FPDMA QUEUED
  60 00 00 00 40 00 00 28 91 cd 28 40 00     00:19:49.384  READ FPDMA QUEUED
  60 00 00 00 40 00 00 42 09 19 28 40 00     00:19:49.384  READ FPDMA QUEUED

Error 164 [3] occurred at disk power-on lifetime: 53155 hours (2214 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 26 d0 9d ee 00 00  Error: UNC at LBA = 0x26d09dee = 651206126

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 08 00 00 00 28 91 cd 68 40 00     00:19:49.385  READ FPDMA QUEUED
  60 00 00 00 40 00 00 28 91 cd 28 40 00     00:19:49.384  READ FPDMA QUEUED
  60 00 00 00 40 00 00 42 09 19 28 40 00     00:19:49.384  READ FPDMA QUEUED
  60 00 00 02 40 00 00 26 d0 9d e8 40 00     00:19:49.384  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 00 00     00:19:49.261  READ LOG EXT

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       90%     53161         651206126
# 2  Short offline       Interrupted (host reset)      90%      8324         -
# 3  Short offline       Interrupted (host reset)      90%      8322         -
# 4  Short offline       Completed without error       00%      8007         -
# 5  Short offline       Completed without error       00%      7853         -
# 6  Extended offline    Interrupted (host reset)      90%         0         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       522 (0x020a)
Device State:                        Active (0)
Current Temperature:                    30 Celsius
Power Cycle Min/Max Temperature:     29/33 Celsius
Lifetime    Min/Max Temperature:     10/38 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        59 minutes
Min/Max recommended Temperature:     14/55 Celsius
Min/Max Temperature Limit:           10/60 Celsius
Temperature History Size (Index):    128 (50)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2           47  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS

