smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p5 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Marvell based SanDisk SSDs
Device Model:     SanDisk SD6SF1M032G1022
Serial Number:    --
LU WWN Device Id: 5 001b44 ...
Firmware Version: X231200
User Capacity:    32,017,047,552 bytes [32.0 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      Unknown (0x000b)
TRIM Command:     Available, deterministic, zeroed
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sun Nov 26 17:28:11 2023 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      ( 112)	The previous self-test completed having
					the read element of the test failed.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x11) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					No Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  10) minutes.

SMART Attributes Data Structure revision number: 4
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  5 Reallocated_Sector_Ct   -O--CK   100   100   ---    -    36
  9 Power_On_Hours          -O--CK   253   100   ---    -    16742
 12 Power_Cycle_Count       -O--CK   100   100   ---    -    87
166 Min_W/E_Cycle           -O--CK   100   100   ---    -    1471
167 Min_Bad_Block/Die       -O--CK   100   100   ---    -    43
168 Maximum_Erase_Cycle     -O--CK   100   100   ---    -    5953
169 Total_Bad_Block         -O--CK   100   100   ---    -    75
171 Program_Fail_Count      -O--CK   100   100   ---    -    9
172 Erase_Fail_Count        -O--CK   100   100   ---    -    0
173 Avg_Write/Erase_Count   -O--CK   100   100   ---    -    5652
174 Unexpect_Power_Loss_Ct  -O--CK   100   100   ---    -    63
187 Reported_Uncorrect      -O--CK   100   100   ---    -    39
194 Temperature_Celsius     -O---K   050   057   ---    -    50 (Min/Max 31/57)
212 SATA_PHY_Error          -O--CK   100   100   ---    -    1
230 Perc_Write/Erase_Count  -O--CK   100   100   ---    -    0 0 48168
232 Perc_Avail_Resrvd_Space PO--CK   100   100   004    -    97
233 Total_NAND_Writes_GiB   -O--CK   100   100   ---    -    182633
241 Total_Writes_GiB        ----CK   253   253   ---    -    52696
242 Total_Reads_GiB         ----CK   253   253   ---    -    669
243 Unknown_Marvell_Attr    -O--CK   100   100   ---    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      1  Ext. Comprehensive SMART error log
0x04       GPL,SL  R/O      8  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 36 (device log contains only the most recent 4 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 36 [3] occurred at disk power-on lifetime: 16739 hours (697 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  51 -- 40 00 a8 00 00 02 46 8e d0 40 08   at LBA = 0x02468ed0 = 38178512

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 08 00 a8 00 00 02 46 8e d0 40 08     00:00:00.000  WRITE FPDMA QUEUED
  61 00 08 00 a0 00 00 01 f6 93 40 40 08     00:00:00.000  WRITE FPDMA QUEUED
  61 00 08 00 98 00 00 02 56 8f d8 40 08     00:00:00.000  WRITE FPDMA QUEUED
  60 00 c0 00 90 00 00 03 36 a1 28 40 08     00:00:00.000  READ FPDMA QUEUED
  ef 00 02 00 00 00 00 00 00 00 00 40 08     00:00:00.000  SET FEATURES [Enable write cache]

Error 35 [2] occurred at disk power-on lifetime: 16739 hours (697 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  51 -- 40 00 00 00 00 03 36 a1 28 40 08   at LBA = 0x0336a128 = 53911848

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 c0 00 00 00 00 03 36 a1 28 40 08     00:00:00.000  READ FPDMA QUEUED
  60 00 58 00 f8 00 00 01 17 af 48 40 08     00:00:00.000  READ FPDMA QUEUED
  60 00 08 00 f0 00 00 03 36 7b d0 40 08     00:00:00.000  READ FPDMA QUEUED
  60 00 98 00 e8 00 00 00 7b dc 88 40 08     00:00:00.000  READ FPDMA QUEUED
  60 00 a8 00 e0 00 00 00 7b db e0 40 08     00:00:00.000  READ FPDMA QUEUED

Error 34 [1] occurred at disk power-on lifetime: 16739 hours (697 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  51 -- 40 00 00 00 00 00 00 00 00 40 08

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  a0 00 01 00 00 00 00 00 00 00 00 40 08     00:00:00.000  PACKET
  61 00 08 00 d8 00 00 01 66 b3 b8 40 08     00:00:00.000  WRITE FPDMA QUEUED
  61 00 08 00 d0 00 00 02 d6 75 78 40 08     00:00:00.000  WRITE FPDMA QUEUED
  60 00 c0 00 c8 00 00 03 36 a1 28 40 08     00:00:00.000  READ FPDMA QUEUED
  ef 00 02 00 00 00 00 00 00 00 00 40 08     00:00:00.000  SET FEATURES [Enable write cache]

Error 33 [0] occurred at disk power-on lifetime: 16739 hours (697 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  51 -- 40 00 38 00 00 03 36 a1 28 40 08   at LBA = 0x0336a128 = 53911848

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 c0 00 38 00 00 03 36 a1 28 40 08     00:00:00.000  READ FPDMA QUEUED
  60 00 58 00 30 00 00 01 17 af 48 40 08     00:00:00.000  READ FPDMA QUEUED
  60 00 08 00 28 00 00 03 36 7b d0 40 08     00:00:00.000  READ FPDMA QUEUED
  60 00 98 00 20 00 00 00 7b df a0 40 08     00:00:00.000  READ FPDMA QUEUED
  60 00 80 00 18 00 00 00 80 82 50 40 08     00:00:00.000  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       00%     16741         18950256
# 2  Short offline       Completed without error       00%       257         -
# 3  Short offline       Completed without error       00%         0         -
# 4  Short offline       Completed without error       00%         0         -

Selective Self-tests/Logging not supported

SCT Commands not supported

Device Statistics (GP Log 0x04)
Page  Offset Size        Value Flags Description
0x07  =====  =               =  ===  == Solid State Device Statistics (rev 1) ==
0x07  0x008  1             188  ---  Percentage Used Endurance Indicator
                                |||_ C monitored condition met
                                ||__ D supports DSN
                                |___ N normalized value

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0002  4            0  R_ERR response for data FIS
0x0005  4            0  R_ERR response for non-data FIS
0x000a  4          187  Device-to-host register FISes sent due to a COMRESET

