diff --git a/conf.d/network.Linux b/conf.d/network.Linux
index 395c1cc6..3c230fe9 100644
--- a/conf.d/network.Linux
+++ b/conf.d/network.Linux
@@ -1,27 +1,27 @@
 # ifconfig under Linux is not that powerful and doesn't easily handle
 # multiple addresses
 # On the other hand, ip (iproute2) is quite powerful and is also supported
-# ip_eth0="192.168.0.10/24; 192.168.10.10/24"
+#ip_eth0="192.168.0.10/24; 192.168.10.10/24"
 
 # Create a bonded interface
-# interfaces="bond0"
-# ifup_bond0="modprobe bonding; ifconfig \$int up; ifenslave \$int bge0"
-# ifconfig_bond0="192.168.0.10 netmask 255.255.255.0"
-# ifdown_bond0="rmmod bonding"
+#interfaces="bond0"
+#ifup_bond0="modprobe bonding; ifconfig \$int up; ifenslave \$int bge0"
+#ifconfig_bond0="192.168.0.10 netmask 255.255.255.0"
+#ifdown_bond0="rmmod bonding"
 
 # Create a bridged interface - let dhcpcd configure the address
-# interfaces="br0"
-# ifup_br0="brctl addbr \$int; brctl add \$int eth1; brtctl add \$int eth2"
-# ifdown_br0="ifconfig \$int down; btctl delbr \$int"
+#interfaces="br0"
+#ifup_br0="brctl addbr \$int; brctl add \$int eth1; brtctl add \$int eth2"
+#ifdown_br0="ifconfig \$int down; btctl delbr \$int"
 
 # Create VLAN
-# interfaces="eth0_2 eth0_3 eth0_4"
-# ifup_eth0="vconfig add \$int 2; vconfig add \$int 3; vconfig add \$int 4"
-# ifconfig_eth0_2="192.168.2.10 netmask 255.255.255.0"
-# ifconfig_eth0_3="192.168.3.10 netmask 255.255.255.0"
-# ifconfig_eth0_4="192.168.4.10 netmask 255.255.255.0"
-# ifdown_eth0="vconfig rem \$int.2; vconfig rem \$int.3; vconfig rem \$int.4"
+#interfaces="eth0_2 eth0_3 eth0_4"
+#ifup_eth0="vconfig add \$int 2; vconfig add \$int 3; vconfig add \$int 4"
+#ifconfig_eth0_2="192.168.2.10 netmask 255.255.255.0"
+#ifconfig_eth0_3="192.168.3.10 netmask 255.255.255.0"
+#ifconfig_eth0_4="192.168.4.10 netmask 255.255.255.0"
+#ifdown_eth0="vconfig rem \$int.2; vconfig rem \$int.3; vconfig rem \$int.4"
 
 # Normally you would use wpa_supplicant to configure wireless, but you can
 # use iwconfig also
-# ifup_wlan0="iwconfig \$int key s:secretkey enc open essid foobar"
+#ifup_wlan0="iwconfig \$int key s:secretkey enc open essid foobar"
diff --git a/conf.d/network.in b/conf.d/network.in
index a0162057..2719fa87 100644
--- a/conf.d/network.in
+++ b/conf.d/network.in
@@ -2,15 +2,16 @@
 # Seperate commands with ;
 # Prefix with ! to run a shell script.
 # Use \$int to represent the interface
-# ifconfig_eth0="192.168.0.10 netmask 255.255.255.0"
+#ifconfig_eth0="192.168.0.10 netmask 255.255.255.0"
 
 # You also have ifup_eth0 and ifdown_eth0 to run other commands when
 # eth0 is started and stopped.
 
 # You can assign a default route
-# defaultroute="192.168.0.1"
+#defaultroute="192.168.0.1"
 # Lastly, the interfaces variable pulls in virtual interfaces that cannot
-# be automatically detected. 
+# be automatically detected.
+#interfaces="br0 bond0 vlan0"
 
 # You can also use files instead of variables here if you like:
 # /etc/ifconfig.eth0 is equivalent to ifconfig_eth0