Bad case: send request to server1good.com; then try to resolve server2bad.com -
this fails, and failure takes ~5 secs; then receive server1's
response 5 seconds later. We'll never sync up in this case...
function old new delta
ntpd_main 1079 1106 +27
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
iproute.c: In function 'print_route':
iproute.c:85:9: error: 'RTA_TABLE' undeclared (first use in this function)
iproute.c:85:9: note: each undeclared identifier is reported only once for each function it appears in
iproute.c: In function 'iproute_modify':
iproute.c:467:36: error: 'RTA_TABLE' undeclared (first use in this function)
Fix it by partially #ifdef'ing the code added in b42107f215
Signed-off-by: Eugene Rudoy <gene.devel@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This particular corrupted file can be dealth with by using "unsigned".
If there will be cases where it genuinely overflows, there is a disabled
code to deal with that too.
function old new delta
get_next_block 1678 1667 -11
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This patch only affects prompts with newlines.
We redraw the prompt [+ input] occasionally, e.g. during tab completion,
history browsing or search, etc, and we expect it to align with prior
redraws, such that the visible effect is that only the input changes.
With multi-line PS1, redraw always printed the prompt some lines below
the old one, which resulted in terminal scroll during every redraw.
Now we only redraw the last PS1 line, so vertical alignment is easier to
manage (we already calculated it using only the last line, but re-drew
all lines - that was the culprit), which fixes those extra scrolls.
Notes:
- We now use the full prompt for the initial draw, after clear-screen (^L),
and after tab-completion choices are displayed. Everything else now
redraws using the last/sole prompt line.
- During terminal resize we now only redraw the last[/sole] prompt line,
which is arguably better because it's hard to do right (and we never did).
- Good side effect for reverse-i-search: its prompt now replaces only the
last line of the original prompt - like other shells do.
function old new delta
put_prompt_custom - 66 +66
draw_custom - 66 +66
parse_and_put_prompt 766 806 +40
read_line_input 3867 3884 +17
input_tab 1069 1076 +7
cmdedit_setwidth 61 63 +2
redraw 59 47 -12
put_prompt 46 - -46
------------------------------------------------------------------------------
(add/remove: 2/1 grow/shrink: 4/1 up/down: 198/-58) Total: 140 bytes
Signed-off-by: Avi Halachmi <avihpit@yahoo.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
It's not clear at all why we do it twice. git archaeology did not help.
function old new delta
date_main 836 839 +3
maybe_set_utc 16 - -16
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
When 'i' or 's' modes are selected block array is filled from offset 3
(blen = 3) but copied to data.block buffer from offset 0 so first 3 bytes
contains garbage from stack.
The buffer that is sent is also 3 bytes too long due to those extra 3
bytes.
Signed-off-by: Avi Fishman <AviFishman70@gmail.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
With new code, we request that target IP (server ID) must be directly reachable.
If it's not, this happens:
udhcpc: waiting 2000 seconds
udhcpc: entering listen mode: kernel
udhcpc: opening listen socket on *:68 wlan0
udhcpc: entering renew state
udhcpc: sending renew to 1.1.1.1
udhcpc: send: Network is unreachable
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1.1.1.1 needs routing, this is fishy!
udhcpc: entering rebinding state
udhcpc: entering listen mode: raw
udhcpc: created raw socket
udhcpc: sending renew to 0.0.0.0
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ going to use broadcast
which is the desired behavior. Before the patch, packet to 1.1.1.1 was routed
over eth0 (!) and maybe even into Internet (!!!).
function old new delta
udhcpc_main 2752 2763 +11
udhcp_send_kernel_packet 295 301 +6
send_renew 82 84 +2
send_packet 166 168 +2
bcast_or_ucast 23 25 +2
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 5/0 up/down: 23/0) Total: 23 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
I see random field values like sll_hatype=0x267 when I strace.
They seem to not matter, but just in case they sometimes do,
let's at least have deterministic values (via memset(0)).
function old new delta
change_listen_mode 308 322 +14
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
This is a must if you need to edit sector 123456789999 on your /dev/disk.
text data bss dec hex filename
922745 481 6832 930058 e310a busybox_old
923023 481 6832 930336 e3220 busybox_unstripped
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
